hi, i was sent here by chris with the turbo quad4 grand am. im searching for a turbo, t3 flange, can be just straight t3 or t3/t4 hybrid, rebuilt preffered...
Well kids, my new old SN93 Paxton supercharger *gasp* has been track tested. Despite a whining ball drive I'll fix over the winter, it made 321 horsepower on a...
I'm throwing this out there not knowing if anyone would want to buy the Fairmont affectionately known as TT460. I'm asking $5500 for the whole thing. The...
/me wishes he had $5500 sitting in the bank... ;-p -r ... http://us.click.yahoo.com/kEZsdA/bwnGAA/YiGOAA/IliolB/TM ... __________________________________ Do...
I have a 50 trim T3 with .42/.48 ARs. It will support approximately 280bhp at high pressure ratios (boost #'s). It has some side to side play and came out of...
I have 2 RHB5 IHI turbos in excellent condition, they are good for about 200HP each. They are watercooled and come with a section of inducer pipe w/ flanges...
Looks like a google search reveals (as accurate as it may be..?). That for every 20 degrees over 170 you go, you cut the life in half of the fluid. Fluid...
FIRST: Remember that it's coolant temperature on the "COLD" side of the radiator. And that figuire of cutting the life in half is IMO bogus, because it isn't...
Ground it off. Splitting the manifold into a bucci - separate front 3 from rear 3 then feeding the spilt scroll Mack truck turbo with it. Don't know if the...
OK, So I'm trying to order the weld el's for a manifold I'm building. Looking at McMaster Carr's website, the sizing of these fittings is ambiguous at best....
Here are some dimensions for some random weld els that I got from McM-C. The first number is the "size," the second number is the as-measured ID, third number...
Wouldn't hurt to install a pressure gauge somewhere in the fuel line. My Ford uses a 1/16 NPT female connection and I plumbed in a line where the Schreader...
Sced 10 1-1/4" pipe has an ID of 1.442" That's what I'm using for my manifolds. If you can find Sched 5 (McM-C doesn't seem to carry it, but it does exist),...
All, Looking at <http://www.ucoatit.com> to coat the concrete floor in my "for parking only" garage. Winter salt dripping from cars has begun to damage the...
I'm using Sherwin-Williams Tile Clad HS in my garage. It's made for airplane hangars, industrial applications, etc. You can get it at any local S-W store. I...
In a message dated 10/3/2004 8:00:46 PM Eastern Standard Time, rodney@... writes: Mark- Wasn't there a very long thread on this about 6 months ago? ;-)...
What make and model is your donor engine??? mart ... From: Peter Straub To: jyturbo@yahoogroups.com Sent: Sunday, October 03, 2004 10:14 PM Subject: [jyturbo]...
... And in case you were wondering... That's an indirect injected I6 diesel. 94/100 bore stroke. 22.7:1 compression ratio. It's going into my Toyota 4x4 so...
... The Sherwin stuff is a poor substitute for the real thing. Go look for Master Builders on the web. Things like Lumiplate and their silane sealers come to...
... I can definitely get into this project as a dieselhead, but I have to say that I wouldn't bother with the complexity of a supercharger/turbo setup. I'd...
... the place to go is www.gwengineparts.com.au. Japanese parts are as common in Australia as ford parts are here. There's a large aftermarket too. A...
I bought a turbo recently that uses a v-band style outlet. Unfortunatly I don't know anything about the turbo, not even a mfg. So I'm unable to get specs on it...
A while back I had saved links to sites that offered adapters for OEM turbos. I can't seem to find them now. Does anyone know where I can find compressor inlet...
the price sounds good ubt if it has play in the shaft its going to need a rebuild and balancing and im trying to avoid that, any shops ive been to want...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
