On mine, they come on with the door and/or the headlight switch in the "down" position. They don't come on at all in the "center" position, and come on...
Howdy ya'll, I finally got my doors dun on my mj. I just replaced them because the low lifes that broke into it cut my speakers out of the doors. i tinted the...
... CJ-10 2wd aircraft tug, uses a Nissan SD-33 6-cylinder diesel, TF727 & NP205 locked in low range driving a D60 rear end. They come up regularly on that...
On my 89 Pioneer, the small plastic tabs were broken and they wouldn't stay in the piller panel. I would up purchasing two new one and they work like a champ!...
This morning i was doing a lube job on the Chasis of my 1992 2wheel drive MJ. Every thing was going great untill i got to the rear part of the drive shaft. I...
If you mean the fitting on the U-joint, these should be greased with a low pressure hand held grease gun. Make sure the fitting points down to the ground by ...
or again if you mean the U-joint you can use a needle attachment for your grease gun ... From: Don To: jeepcomanche@yahoogroups.com Sent: Tuesday, March 01,...
Looks good. I can't describe the rage I felt looking at the carnage pics. It will come around on that SOB.-Rich ... match ... and ... spray ... truck...
Don, When I was doing the lube job this morning i made sure that the fitting was pointed to the ground. When i went to put the cuppling over the fitting it...
A: Check the old ones against some GM car ones. I can't recall which ones I used. but I only had to swap the arms on the back to make them work. ... match ... ...
Actually, my local NAPA(there's a pimp for you Jim) beats Rock Auto's prices on lots of stuff, and matches the NAPA Online site prices. Not to mention Rock...
A: Put in a new line (there should be two going to the front) and maybe delete that load level sensing valve while you're at it. You'll need either an XJ valve...
A: It's not NAPA's own brand. Can't think of the name (Duplicolor maybe?) I did the dash pad and steering column and they were still good a year later, till...
A: Actually, it's a NP208J, not a NP205. They have more low range for tug power. Some come with Dana 70 or Dana 80 axles as well (we have a flock of them at...
A: I'd have to see what style it is, but we have a rubber long tapered tip for some of those (had them at Schucks too. That's part of the CSK chain) BTW, if...
Wow, thats and pretty interesting story :) the fact that you got sued puts the iceing on the cake :) I used that same interior paint in my jeep on the a center...
Guys the brand of vinyl die you want to use is S E M they manufacture a wide variety of matching colors for use on vinyl and carpet, they match very well and...
It's possible that if the UJ was replaced previously, it was installed backwards (the hole for the zerk facing rearward not frontward). Don't ask me how I...
Well guys,I'm going to list my truck on ebay, but I thought i would give everyone in the group a first shot. It is a very nice little truck. Here are some...
Jeff, you will also need the front bearing plate. On the internal slaves, the plate is flat to accomodate the internal slave with which the bearing is...
Scott, Your in Largo! I am around there all the time-Clw/Dunedin. What color is your truck so I can keep an eye out for you. I got a can of the S E M Regal...
Anyone near Seatle need some? I have a pair from an '86 2 dr Cherokee I parted that need cleaning, but aren't torn and work okay. They are blue cloth....
... Cherokee I ... blue ... If you could send me some pictures, I would appreciate it. Seattle is a bit far, but sometimes friends drive back and forth from ...
Thanks Ryan...that's what I suspected. Apparently, the tranny shop tore this tranny completely down, so I'm going to end up getting a big box of parts, not an...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
