I checked my fuel injectors, and all 6 are firing. Plugs are firing also. I figured maybe it's not getting enough air, so I pressed the gas pedal to open up...
I had an old Nissan/Datson pickup a while back (it was free and I owned it for about 2 weeks) and it started and ran dispite having 0 compression in two of the...
I've got those stupid boots on my shocks, so I can't measure how much up travel is actually available on mine, but I have this feeling that would severly limit...
I put in a new timing set, and it had no slack in it at all. I also put in 6 new plugs, and I've seen them each fire. I'm beginning to think maybe I messed...
I can't remember, did it fire at all before the new timing chain was installed? Jeep on! --Pete ... also ... shook ... pressed ... at ... pretty ... be?...
I just saw the guys on Hotrod TV install a Lockrite locker and MAN did they make it look easy! I've seen the installs covered in magazines, but there's...
I read my manual a little more closely. It says when aligning the distributer for installation you must ensure your crank is #1 TDC on the compression stroke....
A: I got a page saying I had to sign in first? http://www.ofoto.com/PhotoView.jsp?&collid=154035789105&photoid=495982199105 From: "Corey" <aerocorey@...>...
A: Check the wires for the CPS (crank position sensor) that mounts on top of the driver's side of the bellhousing for melting (usually to the exhaust manifold)...
Hello im new here and i thought maybe i could get an answer to a question. I have a 89 Jeep Comanche Pioneer. with the 4.0 4x4. About two weeks ago i put it...
Ok, so I picked up the TF904 today.. kinda bummed.. it's electronic controlled.. at least I think it is.. there is a large plug comming out of the side of it....
There is a switch mounted to the inside of your right fender near your firewall, under your coolant bottle I think. It has a vaccum line running to it and an...
Rotated the distributer 180 degrees and it runs like a champ. Starts with no fussing and holds a smooth idle. It's puffing some really dark exhaust, but...
$125 OBO, with lights. No wiring. Located near Chicago, IL. Little surface rust, should come off with a little brillo pad and elbow grease. May need a rivet or...
Here we go again. My grand master plan for this truck has just got a little addition. Now that I have the bracketry, the console, the wiring diagrams, and the...
Correct me if I am wrong - I believe that the term "Lunchbox locker" is reserved for locking the rear up by welding the spider gears. The square box of the ...
This shows how little attention my 86 has required over the years. Not only does the 86 AX-5 seem to have an external slave cylinder, it's on the passenger...
I've always heard those called "Lincoln lockers" after the Lincoln welder. I thought "lunchbox" refered to installing the spidergears- replacing things during...
Not that I think I have any prayer of answering your qustions, but what engine did your 904 come with? And why won't it bolt to the 231? Jeep on! --Pete ... ...
I see some long hair there, but how can we be sure that Rob didn't just buy some stick-on nails and a purse for himself? ;-P Come on Rob, just calmly explain...
Never got it aligned, but I did figure out that I have about 1/2 inch of freeplay in everyone of my balljoints. Found the problem? I think so! Rob L. ... on ...
How electronic can they possibly be? Maybe you can wire it so you can shift it manually? Jeep on! --Pete ... 231? ... electronic ... like ... like ... the ......
Let me get a better pic of the girl, but seriously, I dont even think I'd even be near that good looking, even behind a hand... Besides I am not down with the...
I looked everywhere on the web for a group like this. I owned a '90 Eliminator up in Seattle; and would still have except we moved to Texas and it did not...
