I agree with some of the other commments about a bad fan blowing the resisters. I went throught two set of resistors, and it was not until I replaced the fan...
ongratulations on your new toy. For what its worth, I recently did my bed using Herculiner roll on coating and could not be more pleased with the results....
Rob can you give me a zip code so I can mapquest it. I need to see if I want to dolly an MJ that far. PRL ... s a spare or just wants to get rid of one let me...
I finally got around to cleaning out that horrid expanding foam that rotted a huge hole in the side of my truck. I then cut out most of the jagged, rusty...
Sure thing, McHenry, IL, 60050... If you are seriously interested I will take pics of whatever you want..I would hate to have you drive a good distance and not...
Looks better than mine...I used some of that ghetto metal strip tape to cover the holes, then bondoed the bajeezus out of it. Top-coated with the best quality...
Hey Folks, Well I dont know if you all remember this, but a few months back, the girlfriend blew the D35 rear end in her SFA S-15 Jimmy. So just to get her...
As long as the bolt pattern on the backing plates is the same I don't see why you couldn't do it. BTW I was wondering what front springs you used on the...
Thanks for the response Brian, thats kind of what i figured, but I just wanted to make sure that there is going to be no suprises when this goes together. As...
Hey Ryan: That's what I did when I swapped over the XJ axle to my MJ. Saves having to mess with the brakes when you're done. Everything when together with no ...
This thing has definite possibilities given an extreme lift: Ebay item # 2491245136 __________________________________ Do you Yahoo!? Take Yahoo! Mail with...
Ok I don't know who all has done this wierd dealio but I read a few posts awhile back about building a cabin out of a pallet and burning it down? I built one...
hey, any of you guys have factory skid plates? just got some and It would be great if someone could show me some pics of were these things mount! thanks a...
Looks pretty nice! Check out some of the other trucks the same seller has for auction. I like the 6x6 Kaiser. - Dave ... [Non-text portions of this message...
Sounds like something you would see on the Red Green show on PBS. "If women don't find ya handsome, they can at least find ya handy." and ... keep your stick...
Ugh!! On my 88 4x2, 4.0 5 spd MJ, I plan on replacing the track bar hoping this will eliminate the DW above 45mph. While batheing the bolts w/rust remover, I...
Since I bought the MJ, the gas gauge has been stuck on 1/4. I'm just getting back to being able to work on it after knee surgery, so any ideas? I'll check...
I've got the factory front skid but I took it off cuz it really doesn't do me any good. Two bolts on the right, one on the left and about three in the front...
The Red Green Show is Made in Canada. http://www.redgreen.com/ Sponsored by 3M Makes me proud to be a Canadian :) - Dave ... [Non-text portions of this message...
I found my parts Jeep, I think. It's a '97 Cherokee Sport with an auto trans. It's exactly what I'm looking for to upgrade my drivetrain and interior, but...
My 87 Comanche 4x4, 4.0 is a manual 5 spd Puguet tranny. My front and rear differential has been regeared to 4:11, so I spend most of my life shifting. I...
I have a friend with an xj on 36's 4.56 gears aw4 trans 231 tcase and a 4.0. he gives his jeep HELL! and has for many a year and so far he is still on the...
Yup, the AW4 is one heck of a strong tranny. It's what Jeep has been using since 1987 and it's what you see in every lifted, big-tired Jeep that hasn't done a...
Should just be a matter of getting new bushings and undoing bolts, right? I guess it depends on how much rust there is. I'd start bathing them too. ;-)...
Yes! Pull the cluster out! Don't try to gank the gauge out by itself. It screws in from behind. Undo the dash bezel screw and remove that. Then remove the...
Save yourself a bit of time. Get to the line from the fuel tank, figure out which is the fuel sender wire and ground it. It should make the gauge go up. If it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
