I'm having this problem with my hydraulics. When I raise my snow blower to a given position and leave it there my hydraulic will start to jerk on it's own. Any...
I have a double clutch system on my 434. When I press my clutch pedal right to the floor it takes a few seconds for the gears to wind down. I think it's an...
My 434 has always operated this way, are you saying that is not normal? If your jerky snow blower is mounted on your 3 point lift, the problem is most likely...
Thanks Jeff for the tip on the hydraulics, I'll give it a test. The problem with the clutch is that it takes a few seconds to release the load on the gears, as...
Another possibility is the pilot bearing. If the pilot bearing is beginning to go, or is not properly lubricated, this will happen. Erik ... Thanks Jeff for...
Another possibility is the pilot bearing. If the pilot bearing is beginning to go, or is not properly lubricated, this will happen. Erik ... Thanks Jeff for...
Abe: I have a B250 which does the exact same thing. I did what you mention in the fall: I loosened the pedal, turned the shaft a little then tightened the...
Howdy! I've got a B-250 (BD144) and have had to replace the glow plug indicator (the thing in the dash that lights up when glow plugs are on) about once per...
Paul: I took it into the shop today. I was with him when he took the inspection plate off. He went under with a wrench for a minute ,came up and said problem...
Paul I have a B250 which had a similiar problem. As a clutch wears the pressure plate fingers move towards the transmission until they eventually bottom out....
Paul, Do you have the brass connectors installed between the glow plugs on the engine? The brass connectors create electrical resistance. If you replace...
uh... good question. I have not changed anything since buying the tractor 5 years ago. for the first 2 years I never had a problem, but now basically once per...
Paul, The brass connectors are installed between the glow plugs. You can see them without taking anything apart. They are uninsulated brass with loops on the...
... indicator (the thing in the dash that lights up when glow plugs are on) about once per year/year and a half. ... Hei Paul! I belive if one or more of the...
I was at a consignment auction over the weekend and there was a B414 Diesel with loader that went for $1900 US. The serial number was 48509 which makes it a...
Hi all I have some great copies of the following manuals IH B 414 parts book this is from 1965 great diagrams and pictures price is 22.00 US that includes...
Does the B 414 parts manual have an exploded diagram of the steering box? ... From: rodswinamer [mailto:rodswinamer@...] Sent: Wednesday, March 19, 2003...
yes it does has several pages on the steering sector exploded views plus the steering booster this is just what your dealer would use to order parts from. ...
OK. I'll take one. Can I just mail you a certified check? ... From: rod swinamer [mailto:rodswinamer@...] Sent: Wednesday, March 19, 2003 9:38 AM To:...
paul I sent you payment info directly but a cashiers check is fine. regards rod ... OK. I'll take one. Can I just mail you a certified check? ... From: rod...
Clear DayI believe that I saw this mentioned back last fall by someone, but does anyone have an generic thermostat part number for a 1963 B414 Diesel? Frank...
I found a parts source that gave great service and the prices on used parts were much less than most others quoted. It is Lincoln Supply 479-824-3245 ask for...
I have purchased a British built IH Gasoline tractor that I can not identify. It apears to have many parts simular to the B414 , 354, ect. I was told it was a...
We rebuild water pumps for most makes and models of tractors, including International, Mitsubishi, Massey Ferguson, Belarus, Ford, Case, Allis, Oliver, Hart...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
