Well this past weekend I was able to travel to where the tractor is and the damage is as I had initially thought a broken connecting rod. It has finally...
Even after looking in the manual, I am unsure of the location of the proper place to check the levels. I purchased my B414 diesel last year and want to drain...
The bottom plug is to drain the transmission. The plug by the shift lever (on top) is for filling. The side plugs are to determine the fluid level. ...
Quoting from my operators manual that came with my tractor new on how to check the transmission level. "Remove the oil level plug & the filler plug" (The oil...
Thanks for the direction. It's going to be a big help. I didn't want to take chances. When I do I usually get into more than I bargain for. Thanks again....
Broken Glow Plug resolved Thanks all for direction and advice. I ended up pulling the head. No little bits or pieces of glowplug tip to be found. Better safe...
Sorry for your bad fortune! I have a B275 and bought a bare block on Ebay for $100. Freight was another $125, but all told it was inexpensive in my opinion. ...
I have just taken apart a diesel B-414 due to the PTO not engaging if the engine is running. While fixing this I was wondering what is the proper thickness for...
Hi: I bought the reprinted service/shop manual for the B275/144 diesel, and because I expected that the piston/rod markings would be typical, or shown in the...
I had the same problem 10 years ago and faced mine to the front of the motor. Never a problem all these years. Must of been a good move. Hope this helps. ... ...
Thanks Smith: I'll do that. It makes sense. Now if I could figure which way the rods go. They seem symmetrical..no oil holes or anything. Maybe it doesn't...
... In my notes I had oil holes that had to be placed in line with the rod oil holes to the front as well. After 10 years it is had to remember all the...
I was wondering if anyone else has ever had a runaway engine. Mine decided to take off over the weekend while I was grading the road. No catastrophic damage...
Hi James an engine usually does this when oil cannot run back down through to the sump from the rocker cover.The cause is more than usually high back pressure...
Diesels, particlarly turbos, can runaway on blow-by gases if very worn, but I would first check your oil level in the air filter. Were you grading at steep...
My manual states, "when installing new inserts, make certain that the projections on same engage slots in the connecting rods and cap and that the cylinder...
SSB tractor parts on line has a rebuilt oil pump for $166.32. http://www.ssbtractor.com/Case-International-Farmall-tractor-parts/oil-pump.html about 2/3 down...
OOOPS!! ----- It's about half way down on the right....$141.12 http://www.ssbtractor.com/Case-International-Farmall-tractor-parts/oil-pump.html Bill ... From:...
Well over the weekend I did a leakdown test, Since I dont have a diesel compression tester. 1 & 4 where at about 10%, pretty tight still, 2 was about 25%, 3...
Dont rule it out as a disaster it may just be the head gasket (perhaps)? ... From: James <jimbo_in_nc@...> Subject: [International B Series Tractors] Re:...
My old B-275 always seeped a little oil from where the lift control handle goes into the block under the front of the seat, now it is dripping. A also bought...
I have a 1962 B-414 diesel with a 12V Neg ground electrical system. It has had a single wire alternator for decades and has work well. Now it's dead. I'd like...
come join tractorseverywere. Its a tractor group for all types of tractor lovers and junk collectors. check out all the pictures. there are new pics added...
I also have a 1962 B-414 neg ground and a wiring digram for a genarator. E-Mail me @ jimsmithward4@... and I will get you a copy. I still have a generator...
Thanks, but I have a schmatic of the generator system. I'm looking for the alternator wiring or anything that can help me understand how this system (one wire...
Does anybody know anything about a b414 oil pump.there are 2 different ones.mine has the one with the floating oil pickup screen and the other one bolts...
See message number 3108 and the associated images in the Files section. Terry ... internationalbseriestractors@yahoogroups.com, "Amy,William,Tyler ... ...
I was wondering if anyone has ever changed to the other style oil pump because i think you have to change oil pan also because it needs to be deeper to allow...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
