I have a B-275 for sale. Runs great! Loader, new loaded rear tires, glow plugs work great, starts in the dead of winter like a dream.Have all of the shop...
I just added an album titled "Arty's B-275" with 4 pictures of my tractor that is for sale. If you have any questions, please email me at: rnt2020@......
I just replaced my glow plugs and discovered that the ch28 plugs @ 22.50 ea. do not allow for the fact that the plugs are in series. They have one washer and...
Here at Tractor Home Magazine we work hard on making a nice Magazine to look at and to enjoy. We feature ads from Automobiles, Farm Equipment, Industrial...
Its been along time since I have had some time to spend on this tractor. I have started it a few times and the loud noise is there but it seems like it may be...
Hi This is my first post, I'm in New Zealand and have just joined the group after buying a really original Petrol B-275, to use as a boat tractor. I've owned...
Hi folks. It seems like the tip of a glowplug has broken off and is in the cylinder. Does anyone know of anyway to get the metal out without pulling off the...
Try a shop-vac on a small tube inserted in the plug hole. ... Hi folks. It seems like the tip of a glowplug has broken off and is in the cylinder. Does anyone...
Hi Eric, I just replaced my glow plugs a few days ago because one had too much internal resistance even tho it was not completely shorted out and there is...
Thanks for the replies. I triedthe shop vac to no avail. There is a small precombustion chamber that the plug sits in. I am taking off the fuel injector to ...
I have a 61 gas b414 that had an electric fuel added to it. I put a new mechanical pump on it and know it won't start. Gas is getting to the pump by gravity...
Is there a chance you could have missed the lobe with the pump arm when installing it? You could remove the pump and check the lobe with a piece of wooden...
That's what I was thinking, Bill. I have the same year B275 and on mine, the fuel pump has a primer. If you hold the primer down while you crank the engine...
when i crank the engine the prime handle barely moves,I didn't think it should move at all from the lobe ... If you hold the primer down while you crank the...
Is your cam lobe worn down? Perhaps that promoted conversion to electric? Unlikely, but possible... ... From: internationalbseriestractors@yahoogroups.com...
I'm thinking of selling, but need to know about what its worth. Gas B414, with front loader, Home-made ROPS, Heavy duty 6-way backplade, rear hydraulics....
Well this past weekend I was able to travel to where the tractor is and the damage is as I had initially thought a broken connecting rod. It has finally...
Even after looking in the manual, I am unsure of the location of the proper place to check the levels. I purchased my B414 diesel last year and want to drain...
The bottom plug is to drain the transmission. The plug by the shift lever (on top) is for filling. The side plugs are to determine the fluid level. ...
Quoting from my operators manual that came with my tractor new on how to check the transmission level. "Remove the oil level plug & the filler plug" (The oil...
Thanks for the direction. It's going to be a big help. I didn't want to take chances. When I do I usually get into more than I bargain for. Thanks again....
Broken Glow Plug resolved Thanks all for direction and advice. I ended up pulling the head. No little bits or pieces of glowplug tip to be found. Better safe...
Sorry for your bad fortune! I have a B275 and bought a bare block on Ebay for $100. Freight was another $125, but all told it was inexpensive in my opinion. ...
I have just taken apart a diesel B-414 due to the PTO not engaging if the engine is running. While fixing this I was wondering what is the proper thickness for...
Hi: I bought the reprinted service/shop manual for the B275/144 diesel, and because I expected that the piston/rod markings would be typical, or shown in the...
I had the same problem 10 years ago and faced mine to the front of the motor. Never a problem all these years. Must of been a good move. Hope this helps. ... ...
Thanks Smith: I'll do that. It makes sense. Now if I could figure which way the rods go. They seem symmetrical..no oil holes or anything. Maybe it doesn't...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
