I an re sleeving my B-275 and the manual gives a soap concoction that has to be mixed up (and I will never find around here). What lube do you re builders...
Gday Steve, I just used to use a bit of Industrial hand cleaner (not the gritty stuff)on the "O" Rings and the mating sufaces. NEVER use a steel hammer to tap...
Anyone know approximate weight (within 25lbs) of a B275 diesel engine, bare, no pistons/crank/cam, etc. Just empty block. Thanks much!! Tristan '61 B275 d ...
I parked my b275 this weekend after working it and went to start it sunday and now it cranks but wont start. While working it it maintained 190 degrees and...
i had the same thing happen to me there is a cover under the steering wheel and behind it is some wires and fused and 1 wire had vibrated off took me 4 days...
Gday, Try this, move the PTO lever back gently without dis-engaging the PTO clutch, you should feel and hear the sliding sleeve rubbing on the end of the...
... engine over to see if you are getting any fuel. There is also a plug on the top rear of the injector pump do the same thing there. It may just be air...
Hi Try loosening your injector lines at the injectors and spin the engine over to see if you are getting fuel to them. There is also a plug on the top rear...
Is there a prefered service manual or set of manuals for the B275(1960)? I would like to have a set that covers complete from front to back. Thanks Frizzy...
... harold, the manual @tractor supply has all the info that the hunerd dollar set from that joint in oreogon. i know cause i got both in prep to tear into my...
I have the operators manual B275's covers both gas and diesel versions for 25.00 the parts book for 40.00 and the I&T shop manual for 25.00 plus shipping if...
I finally got some work done on my tractor. So far have put in new sleeves,pistons,pins and bushings,rings,rod and main brgs. Got the pan buttoned up and set...
I haven't posted anything to the group in quite a while but now I need some help. My 62 B275 trip loader has started spewing hydraulic fluid when under load,...
I am in the same quest as Bob but I am looking for a supplier for a spin on oil filter adapter for my B414. A spin on filter would be so much cleaner to...
It sounds like the packing under the 3 bolts needs replacing. When you replace the packing I think you just snug up the 3 bolts and when it starts leaking...
Tired of fighting with rubber gaskets. Just get a better seal and more convenient with the spin on. Bob ... From: internationalbseriestractors@yahoogroups.com...
Ok thanks Steve. So the packing material I will need, is there a particular material I should be trying to find before I pull it apart? Sounds like a ...
- I'm not sure what it has for packing. Any tractor place should be able to help you out. You will also need some sort of packing hook to get the old packing...
Pulled the outer ring off of the cylinder and discovered there is a bevelled rubber gasket that seats inside. It appears to be somewhat chewed on one spot,...
Just another subnote to the benefits of a spin on filter. I don't know about anyone else but my canister filter has a tendency to loosen off with use and it...
Hi Bob, Where were you in Alberta? I live 30km west of Drumheller. Are you using one of the three gaskets that comes with replacement cannister? I am having...
Concerning the Hydraulic cylinders... Mine were leaking significant amounts and after working on them several times I decided to try and have them rebuild, it...
I have the 2" single-acting cylinders from my trip loader here still if anyone can use them... feel free to make an offer I can't refuse. There was nothing...
Could you post some pictures of your hydraulic line hook ups. I was wondering how you managed to run power steering,loader lift,and loader tilt cylinders all...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
