Does anyone know of a Canadian source for a spin on oil filter adaptor for a B275. I have tried the sources listed here and they either do not have the part...
I just aquired a front end loder for my 275 and was wondering if anyone can tell me where to tie into the hydraulics? It has cylinders for up and down pressure...
Hi, I recently bought an early 60s vintage B-275. Seems to run good but it has a big leak of hydraulic fluid from around the control lever on the hydraulic...
Harold, git that thing offa there n farm it out to a hydraulics rebuild shop fer bout a hunerd it ought to last the rest of yer life... you kin tear into it...
Gday Jon, Firstly, if the lift rams have only one pipe going to them (At the bottom) then they are single acting rams which is normal for a loader. This means...
There's a gasket behind the control value housing. They are available from your case dealer and perhaps others. It's a simple fix... Good luck. ... ...
I found this morning that one of my valve springs is broken, I thought I had a tight lash adjuster that was holding the valve open but discovered a broken...
Back in Feb. and March there were some posts concerning spin on adapters. I have a B-275. The posts only mentioned B414's. Will the mentioned adapters work on...
... thought ... If you don't find one by saturday give me a shout. I have a rebuilt head coming saturday so if all goes well I will have one to send you. Steve...
My hydraulic has just stopped and nothing works - the arms or the tipper pipe? All was working perfectly Is the oil in the hydraulic special 0r will any clean...
The first thing I would do is clean the filter and make sure I don't here noises on the suction side at the rubber hose that you disconnect to check the...
The first thing I would do is clean the filter. then I would check the rubber hose you had to take off to get to the filter for dry rot or leaks. If you used...
Gday, Firstly, the knob on the left hand side controls the speed at which your hitch arms or a remote ram will drop. To stop your tipper ram spewing oil out...
... and then I discovered that the button beside the draft top link feature was jammed. The tipper ram must have used up all the oil in my system. The system...
Gday again, That button is part of the top link sensing system for the draft control, its simply a weight transfer system from the impliment to the tractors...
With everyone's spares and parts tractors, does anyone have a functional tachometer and cable for my B-275 diesel? Mine is pretty much toast. I spent $$$...
... internationalbseriestractors@yahoogroups.com, "indoor_roadkill" ... pretty ... having a ... have ... I don't know, it could be an option. It's mounted in...
I have a IH 2000 loader on my 414. It uses a pump run off the front of the engine via a shaft. Everything is self contained and seperate from tractor...
... My 414 also has the same set up with the hydraulic fluid stored in the tubeing that supports the loader seperate from the three point hitch. mine was an...
... of ... from ... Does a 414's hood not open tilting forwards like a 275's? How do you open the hood with a pump in front of the grille? That was an option...
I made a couple of poor choices this weekend: 1. I shouldn't have tried to cross that ditch, it was too muddy. 2 . I should have asked for assistance in...
I have the same problem, and no the hood can not open with a pump and loader. I have to unlatch my hood front and back and lift it up to get at the engine....
Yeah, it would have been far too easy if they had designed the hoods to pivot somewhere useful, like at the radiator or something! I wonder how hard it would...
I have thought about the same thing on how to tilt my hood, but have not come up with a good idea with out major redesign. If you have any thoughts on how to...
I don't have a front end loader, but the first thing that comes to my mind is a pump that you can slip on & off your pto shaft like the ones they use with...
Thanks to all for the info. Got the thing mounted and tied into the hydraulic system and it works good except it is very slow running off the existing pump. I...
Thats fine if you don't need the PTO, but I use it for mowing and snowblowing etc. I considered putting it on valves that can select between an external pump...
Greetings everyone... I own and use a 1964 B275 (Diesel) around the farm all the time... Have been having trouble with the front end loader not working well...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
