Sorry I missed this one, I was on a 5,000 mile, 10 day bike trip through the Western US (Utah, Colorado, Arizona,...) on my basic VFR, but my two cents. I had...
Does anybody know if Ian Clint is genuine with the parts he posted for sale? I made an inquiry, he responded once, but then nothing. I still want the parts if...
Rick, I have not conversed with Ian (via Yahoo Instant Messenger) in a while but I did buy a NC30 front wheel (3.5 x 17) and a rear Maxton rear height adjuster...
Rick, Ian Clint is very trust worthy and is good for his word. I've dealt with him on many things over the last years and have always walked away with a smile...
Thanks guys, Ian has helped me out (with words) before and seemed sincere but thought I'd check. I'm not in a rush really, just wanted to know whether to...
I've also dealt with Ian on a number of occasions and infact was only up with him about four weeks ago. I have found him a very nice and genuine guy. I think...
For all you 45er's out there who haven't seen it, there is a twin exit (either side) WSB spec downpipe set on ebay. No silencers, reserve not yet met @ £16. ...
Ian's a top man, I think the parts he was offering were on behalf of someone else. There was certainly a long list that was, and when I enquired about a few...
Clean Washington state title under bike VIN#. Jha pipes, Vortex rear-sets, Lindemann forks, F4i rear shock. Rothman's livery stock, stock mag wheels....
Dries, Here in the US, I can get the V-rod tire from MAW for around $120 or so, and get mounted balanced for around another $15-20. We don't have the 207RR...
... of someone else. There was certainly a long list that was, and when I enquired about a few bits he replied that someone was talking to his friend about the...
Rich Ain't it nice living in a society with such a competitive economy! Here in South Africa, the only place you're going to get that V-rod tyre is from H-D...
Hey guys, after two successful seasons racing the RC30 finishing Runner-up two years on the trot with the open-superstock reguarly beating far more powerful...
After a couple of years parked-up I finally got my RC out again yesterday! It's gone through a bit of a rebuild, brakes (PFM cast discs, EBC HH pads, new seals...
I fitted a brand spanking Micron system to my RC several years ago, nothing fitted properly, the rear right downpipe fouled the frame, very few of the spring...
Hi, My name is Lois and I run a company called Hi Lo Biker.com. We make CUSTOM Motorcycle patches 1 to 1,000; no you do not have to have a lot of money to...
Hi, I've experienced the Micron 'fits where it touches' RC30 system myself, but Mike's probelm is much more than just a fitting job. There is something...
I am looking for a good home for a used Marchesini Magnesium 5-spoke front wheel for the RC30. There is also a set of matching Brembo disks. Size is 3.5x17 ...
, ... Richard, My full system non deep sump fits well but the slip on with its associated pipework is an awful fit and keeps moving about. I looked at both...
Dave, Many thanks for this info. We suspected that the final 'Y' piece might be different and having suggested that is the case, you may have helped a lot -...
Dave, By the way, for the avoidance of doubt, the existing (we suspect deep sump) 'Y' piece gives an angle that is much too steep - i.e. the end can is...
... Richard, If you look back at my original reply you will see I refer to both the full system and the slip on system. I cant see why the d/s and non d/s...
Thanks Dave. Mike and I were comparing a deep sump and non deep sump - both full systems and they are distinctly different right through to the final Y. The...
Richard, I only picked up on this Micron issue yesterday. Shame because I'd have pointed you to the album section 'Jeroen's bikes' where you can see the Micron...
Hi I have a problem with my 30. The problem is hesitating/bobbling betwen 5-6000 revs.At the Dyno it was not there , but it had no fairing and fuel tank on the...
Hello Jeroen, Thanks for you comments and pointing me to your pics. It does show exactly what Richard and I thought , as the pics of your NDS system's last 'Y'...
Mike, I'd have to take a look at home to see how close it actually is but in practice it never caused a problem and it is not critically close. This bike is...
Jeroen, The pics are great, wish I'd seen them earlier as I was beginning to think I'd lost my 'mechanics touch'!!! Frankly, I'm just glad that Mike is now...
Hi all, Just came back from a track day at Laguna Seca where I had a great time. However, while there a seemingly well versed gentleman approached me about...
