Jeff,<br><br>You are correct.......the Japanese, NZ & Aus bikes came with the smaller indicators.<br>They will fit the rear no real problems but the front is...
Hi, all<br>I take it you are all now aware that the HRC race kit manuals are now available on line for download via the Technical downloads page on my site. If...
Guys,<br><br>Have had stacks of interest in the poster but the other parts of my friends have gone relatively unnoticed. Spoke with him last night and he has ...
Hi, My German import RC30 has the original 'Ducati' style flip up side stand still fitted. Although I've not yet had a serious look at it yet - has anyone ...
Hi Glenn<br> Did one last week. Remove side stand. Look at the back and you'll see a peg sticking out on the centre pivot bolt. Cut it off. Refit side stand....
Hi guys,<br><br>can someone give me some advice on the fitting of a Dymag front wheel?<br><br>I have a new Dymag front Racing Magnesium wheel and I am in the...
Hi Paul,<br> I've fitted Dymags to other race bikes but not my RC. Has your wheel come with bearings ?<br>If I think back they used to take 6204 RR ...
Paul,<br><br>It was some time ago but I used to have a set of the original 3 spoke Dymags and they never had dust seals in them, come to think about it neither...
Col/Clinty,<br><br>the wheel is supposed to be a direct replacement for the standard RC item and has come fitted with spacer and bearings. The bearing number...
Paul,<br><br>More importantly have you measured the distance of the std wheel between the bearings, as I have a feeling this will be the same as the Dymag.Is...
Does anyone feel that the extra 1/2 inch between the stock 17/3.0 and a 17/3.5 F3 rim makes much of a difference for street riding. perhaps the only difference...
Paul;<br> I installed a new set of Dymags to JT McDonalds RC30 a short time ago (five spoke) and there is no problem with the stock front axle fit. Early ...
Paul et al,<br><br>Not regarding Dymag but a similar issue - I fitted a Marchesini 3.5 front recently and had a similar concern with lack of dust seals etc....
Jim,<br><br>I have just read your message after my reply to Paul re std axle - PANIC!!<br><br>What happened to your rim (what happened to you?)<br><br>Tom.oz...
Tom; Long story, basically I needed to replace my HRC axle and decided to machine off .250" from the fat end of a standard axle, the part that inserts into the...
Here's a head scratcher!<br><br>Has anyone got a Race Programme from the Suzuka 8 Hour Endurance Race 1987?.<br><br>Has anyone got any ideas where i might get...
Hi,<br>Firstly the difference between the 3.0" and 3.5" front are that on standard geometry the 3.0" gives better turn in but offers less contact patch once ...
Hi Paul,<br> The guy from Dymag is right in what he says, if the bearings are shielded just ignore the<br>std dust seals. As long as the distance between the ...
Hi Joel,<br> I agree, I think the rubber is more important than the rim width. I used to run std<br>rims for racing, ( couldn't afford HRC rims! ) with Dunlop...
Thanks for all the info. I did put a Pilot Sport on the front and it suits my street riding just fine. However, my rear end is all over the place, like a cheap...
Tom,<br><br>yes my ID does indicate my other money pit. If you have experience of these though I'm sure you'll understand why it demands as much attention as...
Hi guys,<br><br>the wheels I have are new 3 spoke Dymags and I haven't had time yet to take out the axle from the standard wheel. I'll check the standard ...
