...are you being funny? J. Mark Locklear (225)803-2302 -Philippians 4:13 "One machine can do the work of fifty ordinary men. No machine can do the work of one...
I have never owned a motorcyle before, and know little about them.. I want to learn. I have an opportunity to purchase a Hondamatic motorcyle in very good...
Mike, This question comes up alot. Best answer I can give you is...it depends. Which Hondamatic are you talking about? 750 or 400. The 400 is a relatively...
I've said many times that, if I were just starting out as a m'cycle (vs. scooter) rider, AND I knew that such a thing existed, I'd definitely want to start...
Thanks for the comments. The bike I am looking at is a Hondmatic 750. It's in superb condition too. Everything I have read and heard so far indicates it's a...
Well today I got the top half of my air box on and connected two out of three vacuum lines (are they vacuum - not sure). But the last one that goes over the...
Jamie, I'm not sure which lines you mean. Can you post some pictures? There is a bowl vent fom the carbs that just vents to atmosphere. Maybe that's the one...
...well, yeah...it is kind of funny. 240 tires are generally reserved for wide tire choppers. But to answer your question seriously, you will not find a rim...
Well this is a small diameter line that is attached to the top of the air box with a hose clamp, one end of the hose I attached to a line that connects to the...
http://www.cyclexchange.net/Honda%20Page.htm These people have offset sprockets for Honda 750's. As well as a bunch of other neat stuff. Check them out. Joe ...
yes exactly what i am doing ...i want to spoke the original drum hub to a 16x10 rim ...extend the sprocket ...fab a swing arm with an included jack shaft...
Joe, sorry I underestimated your imagination. You can try http://www.buchananspokes.com/ . If they can't help you on the spokes, maybe they know somebody who...
Jamie, What year is your bike? I've looked at mine a couple times and I can't figure out what line your talking about. The manual shows 4 carb overflow...
Are you looking at the line from the Idle module to the air box? Wolf ____________________________________________________________________________________ Be a...
Yes, One end (front facing) I have going to that Idle pot vacuum set up the other end of that hose goes no where right now and that idle bump up is not working...
Jamie, What year is your bike? There is a difference in the idle system from 76 to 77. They are wired differently and have different components. There is a...
I've been fighting wet weather problems for a long time now. Early this year I did an ignition upgrade with new coils, wires, and a CD ignition box from ...
I hope that fixes your problem, but how do you think that much water is getting in there when your riding? You must be riding in some pretty wet weather! ...
It was at it's worst in a fine mist, like road spray from other vehicles. Most of the time in a regular rain with nobody around, it would run. I once hit a ...
Ive been looking for info on these bikes, I found one at an estate sale in a barn in North Florida and have been looking for info on a rattle in the motor,...
Charlie, It's hard to say if it's the cam chain without hearing it, but most likely it's not. The sohc Hondas are known for a rattle from the engine when...
its at low RPM making me think it was slack in the chain...but I will look into the other things you mentioned..it does knock like a desial...is there a web...
The engine may not be running on all cylinders evenly. That can be be caused by many things,one of them is that the carbs are out of "sync". But usually a carb...
Hi! I am in the process of changing the chain and both sprockets of my '77 CB750a I have the Clymer manual, but it is of no help on the front sprocket. I have...
Angel, It's a lot easier then that. All you have to do is remove 2 phillip head screws to remove the rear cover to access the 2 bolts that hold the sprocket...
I have a Hondamatic 750 electric starter spins free out of bike but when I put the starter back on the motor it will not turn the motor over? I hot wire the...
its on the left side of the bike by the shifter,in front of the foot peg.. it is covered by a black rubber cap..BE SURE TO TIGHTEN THE KICK START LEVER OR IT...
Saw the other post . Can you rotate the engine? You may half to take a plug out to fell the compression . Is the battery up? If not,it will turn under a spin...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
