yes me too. When buy a house (whenever that will happen) i will buy another nighthawk possibly wrecked (but not too much) to fix it and feed my addiction. I am...
shot in the dark: did you tap all along the brake line in case you have an air pocket that keeps putting air in your system? plus unscrew the caliper from the...
Yeah, I have, but I was going to do it all over again anyway. I was thinking of draining and checking the caliper, replacing the bleed screw and all the crush ...
Mark, Tell us about the compression loss. How many miles on the engine? Is the low compression evident in all four cylinders? Did it happen suddenly? Can you...
Did you say PLEASE when you asked her? Michael A. Alvarez 2003 Red NH 750...My Precious! 40k Miles and Going Strong ... Relax. Yahoo! Mail virus scanning helps...
* Paul Bater (paulbater@...) [060301 10:38]: ... I'm not an expert by a LONG shot, but, if it were me, I'd wrap the bleed valve threads with teflon tape ...
According the the manual it specifically says pistons can still be worked on without taking the engine apart. Of course, this engine may be different enough...
I have a couple of issues I need help with. I have an 85 650 NH. First, I installed a new right front turn signal and it blinks twice as fast as the left...
Hi everyone. My name is Braydon. I just jonied today and I can't wait to talk to everyone. I am getting a 1983 CB550SC this weekend. I have read that the old...
Paul, I found it i sbest to put a tiny hose clamp round the bleeder tube, so air cannot get back in. I had the same problem you are talking about up to then....
hello all my name is james and was just recently given a nighhawk. i have several problems with it the first thing is that when i go connect the postive...
Wave, If it's a 91 or newer 750 NH, it should have a silver crush washer that should be replaced every time you change the oil. I'm not sure about a copper...
Half the fun? Not sure I'd put it quite that way. Still, though, if you can practice the mantra, "This is a learning experience ... this is a learn...."...
... The flasher is thermal... if you have corrosion on your wiring harness connectors (or bulb connectors), the more-corroded side will be higher resistance,...
... That would be a shorted starter relay. Either the relay itself is stuck closed, or you have a short somewhere in the wiring between the starter relay and...
I've had the same issue with the previous battery, and yes the lights do get brighter when I rev up the rpm's. I also forgot to mention that the turn signal...
Check that you connected to the proper wires (same color to same color) for the turn signal. If not, this can cause the signal to blink faster and brighter. ...
Er, does that turn signal double as a running lamp? Is it twice as bright when flashing, when working as a running lamp, or both? Well, if your lights get...
The bulbs are the same. Just for kicks, I bought 2 new ones & it still does the same thing. The front turn signals do act as running lights also. The...
It's not the oil drain bolt and washer. Clymer mentions it specifically so as not to miss when bolting up the oil pan. It is on a specific mounting bolt...
Greetings, I'm definately going to need a fork seal replacement very soon. I am pretty much limited to my local Honda dealership for the work. Can anyone give...
When I bought my NH650 last year, the forks were spewing oil. The local dealership quoted me $200 plus parts!!! I wound up buying a set of forks on eBay that...
Welcome to the board, Braydon! I would wait to buy a new seat until you have ridden your "Hawk" for a while. You may find that the seat is just fine. I...
I bought seals and rings on line for about $16. I plan on doing the work soon. Before you do, make sure you have something to measure the depth of the ATF...
I use it in the kids bike tires, and in an 'all-terrian' running stroller I have (has bike tires) - in those applications it doesn't adversely affect a thing...