most of the steps are probably in preparation for winter rather than after the winter. I can't imagine much coudl go wrong in a few months though. make sure ...
hi all, I have oil pouring from the small hole located just under where the crankshaft protrudes from the engine side (I am assuming its a seal goneinside...
Ben Just go to this page http://www.servicehonda.com/gsearch/gsearch.asp And type 08111 as Item number and you should find what you need. Good Luck Ron G. BLK...
Just so some of the newer guys know, the sissy bar for the CB650SC is as scarce as hens' teeth. Thye aren't making them anymore and, so far as I know, there is...
I will contact a friend that knows him and try to get some pictures and a price and more details, hopefully by monday. ... exactly ... a ... actually ... like...
Hi Al; I've heard that the shift linkage can get cruddy and bind at the knuckle. I'm not sure if the 650 linkage is like the 750, but you might want to check...
Ok first things first... What steps to I need to take to remove and replace my plugs? What plugs should I use? Do I have to remove the tank? If so how!?! I can...
Well, that does not sound good, but you need to provide a much more specific description if we are to have any hope of helping you. To begin with, what model...
The subject of this post says "700s"....that would be the Honda Nighthawk S or CB700sc. Produced three years from 84-86. You have the same bike. ... ...
I'm not sure about your model, but there may be a drain tube coming off the bottom of the airbox that needs to be drained periodically (there's a plug in the...
i just bought a F 16 Sport shield by National Cycle. My local bike shop got it for around $100 bucks for me. It is not the short tinted one, but the taller...
Regarding the rear end breather, they do occasionally blow out some oil vapor -- that's what they are there for. but, if you haven't replaced your final drive...
Doh! I knew there was a reason why I pulled out my service manual as I read this post. Yet the post itself did not ID the bike. Point taken, but still, more...
This is funny that they don't make them but they still list a part number for them? When I bought my 700 S last year I went to 3 or 4 dealers looking for...
I am interested in the engine guards. Can you give me some guidance (part numbers and web site)? Did you get them in black? I checked the numbers on your...
P.S. Remove the left-hand side cover. If you are lucky, the previous owner left the original Owner's Manual in a plastic pouch attached with velcro to the ...
Ben, When I change my plugs, I pull the tank, which requires you to pull the seat first. So, pull the seat (two bolts, one on either side of the bike near the...
In a message dated 1/30/03 10:23:34 PM Eastern Standard Time, ... In just one term, I'll say....... STEERING HEAD BEARINGS!!!!!! Have them serviced, it'll do...
StlthHsta@...
Feb 2, 2003 2:18 pm
17779
The part number for the engine guards for the 700 S is 08151-MJ100 that is chrome I don't know of a number for the black one, never seen one. Ron G. BLK & BLU ...
I have a Rifle fairing (I think it's called either "Superbike or Nightsomething) put on by the PO. Not bad: It's a little bulky, though, and I like the Givi....
I use a Streetshield by National Cycle, & like it very much. I purchased it a few years ago from MAW. Cost approx. $65. ... From: maxrates <maxrates@...>...
... got ... Hi there, I have a spare flasher relay (a few actually, I'll let it go cheap too!). As for the starter clutch, I have one of those too, but haven't...
... got ... Hi there, I have a spare flasher relay (a few actually, I'll let it go cheap too!). As for the starter clutch, I have one of those too, but haven't...
... got ... Hi there, I have a spare flasher relay (a few actually, I'll let it go cheap too!). As for the starter clutch, I have one of those too, but haven't...
