I remember a while back some suggestions on places to take the Grilles to get re-done. I had all the anodizing stripped off today for a measly $10 bucks....
I have a precut carpet piece for the consoule in medium blue 08. This is a die cut piece purchased from Auto Custom Carpets for a consoule I restored but we...
Yeah I would agree with that Maynard, that all the consoles are gonna use the same rug and then it is a cut to fit. I used an Auto Custom piece on my car and...
- Yeah well hello Jon good to hear from you also, hope all is well. I guess I could bing you and the group up to date on the GTS. I finally tracked down the...
GTS ONLY CARS and/or PARTS WANTED: List your needs here. Include your email or phone contact info in your listing. Keep it GTS oriented. This "FILE" will...
gtsbulletin@yahoogrou...
Sep 2, 2006 10:05 am
2711
I would think that re-anodizing is required to keep the surface from dulling from oxidation again. The trick with polishing is to get out all of the little...
Missed seeing you this year too, Maynard! Now that I am unemployed I have bee travelling all over the country enjoying myself. I will be in St. Louis for...
George, I just looked at the photo's and it looks like you attached the thumbnails instead of the pictures. I cant get them to enlarge past the size of a...
Well, I finally got the wife to drive one of the cars so I could get some together pictures. I know I haven't posted much, but I've been busy switching the...
OK, need some more info for correct detailing on my 69 GTS. Inside the trunk, where is the most common location for the jack instruction decal? Also, whats the...
... the ... know ... is: left of center as your standing facing the open trunk lid. But I've seen it to the right of center also. I think its 50/50, all...
I loaded a couple of picture in the "Yahoo Photo Album" in the PHOTOS section. One is the location of my original trunk sticker, and the other is of the jack...
Hi guys. I need a better rad cooling fan other then the stock #213 fan for my big block GTS. I need something that draws more air because the motor tends to...
Don, do you have a 614 shroud? I never had problems with my 065 as long as I had a shroud on it. If you want to recore the 065, send it to Glen-Ray Radiator in...
... little warm especially in traffic or at slow speeds, or at stoplights. I was thinking maybe a fan with more pitch mite help draw more air and keep it...
Don, call Bob at Glen-Ray Radiator at 715-842-3352. Rhino ... little warm especially in traffic or at slow speeds, or at stoplights. I was thinking maybe a fan...
Don: does your 383 have a fan spacer between the blades and pulley??? I assume your fan is just that-a fan. I, too, suffered from overheating problems with my...
... the #614 stock rad shroud, and a 50/50 mix of Prestone. All is as it should be. My guess is its the larger Comp Cam (about 3 steps up from stock cam) that...
They only offer one kit for the clutch fan kit. According to Mancini, it is listed for the BB only, but it does work on a LA engine just fine.............. ...
Frank: Your right, thanks for showing me the error of my ways. Why the hell did I pass on the drags for a cruise. It must have been temporary insanity :0) I'll...
While we are on the subject of cooling, Does anyone know if this kit will work on my 383 Car? I want to go with the viscous fan. I now have two radiators to...
Dave: My car is also a big block. Frank tell me this viscous fan package that Mancini sells works for both small & big block motors. Don... ... go ... Both ......
I believe it was actually designed for use with the big blocks and then was co opted for use on the SB A/C cars Works for both and both Frank and I can attest...
Does anyone have an extra of the above??? I went to install my mini starter and for some reason can't locate mine!! I would appreciate any help!!!!!...
Hi guys. I have a question pertaining to under the hood factory markings, specifically the drivers side valve cover. I've notice on some show cars a 3 digit...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
