The V2 list is not an option for me. I was kicked off the V2 list a couple years ago because I angered Saffo...plus I didn't edit my replies. Chris O'Rourke ...
hello guys,just seeking some opinions on why on a 1989 st165,the check engine light is not being activated when the ignition is turned on.i also tried pulling...
(1) the atmosphere is friendly and relaxed. We do not welcome abusive language or profanity. We are also thankfully short on flame wars, so let's keep it...
gt4@yahoogroups.com
Oct 1, 2005 5:40 pm
101429
LOL. The following email was sent on September the 28th..........it has been in the dead email letter office for three days evidently. Just thought I would...
Hi, I too have poly bushs supplied by supepro and whiteline.i have had the same issues with mine, both sets . I recall this was spoken about some time ago and...
... Yep, I'm still gonna be reading the list and answering where and when I can. I soon my not have a GT-Four though. I recently bought a WRX STi, and I wasn't...
Hi, Just ordered some TEIN SS coilovers for my 90 All Trac. I drive mostly in the twisties on smooth roads. Any setup suggestions? Also ordered a Whiteline...
Did you verify that the E1 wire is getting a good ground signal at the check connector and at the ECU? Sounds like the ECU is not getting power or has a bad...
Are you referring to the rear bushings? I went with the camry spherical bearings for the rear control arms, and Superpro poly in my (rear) trailing arms. The...
Hi, Did you notice a improvement using the stock Toyota bush? Steve Gillies Golf GTi ST 165 88 uk (BETSY) 310 BHP 1/4 mile 13.4sec @ 103 Sussex In dry Dock...
I don't have it on the road yet. I also will not likely be able to give a good opinion, since I'm doing full bushes all around, a new rear swaybar, and a...
Hi all, after a few opinons on running in a rebuilt engine, new over sized forged pistons, new bearings, good used crank shaft, new oil pump etc i have read...
Steve, I've got a procedure that I'll email you offlist (it's an attachment). What's your email (it doesn't show in the header)? Brady ... [Non-text portions...
Hi Dennis, Thanks for making the announcement, and for the opportunity. Hopefully we
can keep the GT4 list active for many years to come, and share information...
Useful Info: Check out the new FAQ at: http://www.rennison.info/newgt4faq/index.php Unsubscribe: gt4-unsubscribe@egroups.com...
gt4@yahoogroups.com
Oct 9, 2005 4:21 pm
101445
http://www.trademe.co.nz/structure/show_member_listings.asp? searchtype=SELLER&member=342593 Let me know by email if you want anything or just bid on them. Tim...
Hello listmembers, I'm about to transfer some parts from my old car(black ST185,DESTROYED! by some ignorend *#*hole on the highway) to my new car(red ST185). ...
Hello Greetz, Do not use more than 1bar of boost pressure. regards, Stephen Gunter GT-Four list owner. ... From: Remco van Stroe Date: 10/12/05 14:39:53 To:...
Dennis, sorry to hear you might have to get rid of your GT4...at least it has been good to you. Just want to say, your posts here and your collected info on...
Personally I recommend 12 psi is max for the stock setup. I believe that 14.7 (1bar) might be to much. Though I'm know expert either. Steven has been in the...
Hey! Raises hand....what about me. ;) Hahahha Speaking of the old days....I got my 165 out of storage last week. Dusted off and finishing the fuel system as...
So I finally got all the bushings installed - properly, I think - and the results match up with what I'd read from others. You can feel small bumps and cracks...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
