Hi Group, Does anyone have Tom Van Beek's email address or phone number? Thanks, Larry Gammon. [Non-text portions of this message have been removed]...
Louise & Larry Gammon
llgammon@...
Oct 7, 2005 6:17 pm
1215
Larry: The last email address I have for Tom is _tvanbeck@..._ (mailto:tvanbeck@...) . That address is a couple years old and don't know if it...
Bjwt56@...
Oct 7, 2005 6:32 pm
1216
Hi John, Is it Van Beck or Van Beek? Larry. ... From: <Bjwt56@...> To: <goldenfin@yahoogroups.com> Sent: Friday, October 07, 2005 12:32 PM Subject: Re:...
Louise & Larry Gammon
llgammon@...
Oct 7, 2005 7:03 pm
1217
Larry: In my rolodex I have it as Van Beek. John [Non-text portions of this message have been removed]...
Bjwt56@...
Oct 7, 2005 7:20 pm
1218
Larry: I just looked at my rolodex again and I see that the email should be _tvanbeek@..._ (mailto:tvanbeek@...) . John [Non-text portions of...
Bjwt56@...
Oct 7, 2005 7:21 pm
1219
Hi Group, Does anyone have a good experience with a manufacturer of correct fitting tail pipes for my 56 Fury? Thanks, Larry Gammon. [Non-text portions of this...
Louise & Larry Gammon
llgammon@...
Oct 12, 2005 2:15 am
1220
Hi Larry, Took me a while to find this reference which is several years old, (friend used them for his 300-D) but this vendor still going strong - Classic ...
William Lewis
reatawhippets@...
Oct 14, 2005 11:21 am
1221
Hi Jack FYI-----I put a stainless system on my 57 FURY . I bought it from WALDRONS They were very polite and helpful and the price wasnt bad. But the fit left...
Hi Jack, Thanks for the information. I have asked for a quote. Do you have any leads on the special exhaust deflectors? I have found an N.O.s. one & need one...
Louise & Larry Gammon
llgammon@...
Oct 14, 2005 4:39 pm
1223
Ton Mitchell once told me that the exhaust deflector - not sure sure which years it covers - is the exact same as the Studebaker Hawks - I think 1956 - and ...
ArthurWLinden@...
Oct 15, 2005 1:53 pm
1224
Hi Group, Found a new windshield (at great expense) for my newly painted 1956 Fury. Now I need the best pre formed reproduction windshield gasket I can find!...
Louise & Larry Gammon
llgammon@...
Nov 4, 2005 4:05 am
1225
Might try KARR RUBBER, ElSegundo, CA Bob [Non-text portions of this message have been removed]...
furylvr@...
Nov 4, 2005 5:22 am
1226
Hello Larry, Here is the link to Steele Rubber Products for the front windshield gasket. Runs $126.50 for the rubber gasket. (800) 544-8665. ...
Ed Dea
ed_dea@...
Nov 4, 2005 9:03 am
1227
Hi GFSers, A '56 Fury is up for bid on ebay, a 7 day listing with 6 days, 7hours to go. Item #4587513256. This car was owned by Joe Craig for 20 years and...
William Lewis
reatawhippets@...
Nov 5, 2005 12:46 pm
1228
Hello Ron: On May 2, 2004 you sent an email with your take on the 2x4 manifolds for the 56 Plymouths and Fury's. Since then I have been researching and ...
Bjwt56@...
Nov 5, 2005 9:18 pm
1229
Ron: The square pattern 1735919 manifold could be drilled for the bigger WCFB carburetors, but the "clover leaf" holes would also have to be made larger. ...
Bjwt56@...
Nov 6, 2005 2:12 pm
1230
[Non-text portions of this message have been removed]...
Bjwt56@...
Nov 8, 2005 8:58 am
1231
Hi Group, Looking for information on wheel & tire combos for a '56 Fury. I have ordered some 15" x 6" wire wheels for my Fury. Still pondering tire sizes. I...
Louise & Larry Gammon
llgammon@...
Nov 16, 2005 11:24 pm
1232
Larry..... If will likely depend on the setback of the wheels you are getting. George ... From: goldenfin@yahoogroups.com [mailto:goldenfin@yahoogroups.com] On...
George McKovich
george@...
Nov 17, 2005 4:38 am
1233
Hi George, I am looking at 4" back spacing. Thanks, Larry. ... From: "George McKovich" <george@...> To: <goldenfin@yahoogroups.com> Sent: Wednesday,...
Louise & Larry Gammon
llgammon@...
Nov 17, 2005 5:50 am
1234
_Click here: eBay Motors: Plymouth : Fury (item 4588466471 end time Nov-18-05 11:37:54 PST)_ ...
25% DISCOUNT CHECKOUT COUPON CODE FOR FACTORY CD-ROM MANUALS FOR GROUP MEMBERS. MOPAR MANUALS ON CD-ROM by MUSCLECARS IS OFFERING UNTIL DEC 15TH 2005, A 25%...
Hello Group HAPPY NEW YEAR!!!!!!!!!!! To anyones knowledge,,,has there ever been a 'PRODUCTION STICK FURY' with OVERDRIVE??? I would think not--but please let...
The overdrive was not recommended for some engines. The overdrive unit would not handle the torque of the G.C. engine and no plans were made to improve the...
I know some friends already who have met a few nice honeys off of this kind of stuff (here is the place they use: http://www.whereyougethookedup.info/ziok ,...
georgette-murdock399@...
Jan 11, 2006 1:01 pm
1241
Sorry folks. This person is now banned. -Dave ________________________________ From: goldenfin@yahoogroups.com [mailto:goldenfin@yahoogroups.com] On Behalf Of...
Here is a new software product available to assist in the restoration of your classic automobiles. Please visit my website http://www.restorationassistant.com...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
