FURY Meet 2005 JULY 8-9-10 Carlisle All Chrysler Products Nationals Information for Fury owners, and friends. Click here: Cars at Carlisle - 2005 Carlisle...
In need of brake "c" clip--part # 308246. This is the clip that retains the brake shoe to the anchor bolt on the '56. Need all 8--had the brakes apart too...
furylvr@...
May 30, 2005 5:18 am
1106
I am looking for a pair of motor mount housings for a 1958 Fury 318 motor. Also, any info on where to find the studs that hold the backing plate to the...
Wht don't you try Andy Bernbaum he might have the part you are looking for Steph furylvr@... wrote:In need of brake "c" clip--part # 308246. This is...
Steph Burlew
sb57fury@...
May 30, 2005 12:44 pm
1108
Why don't you try Andy Bernbaum or JC Whitney and see if they have the part you are looking for steph rob42861 <rjn42861@...> wrote:I am looking for a...
Steph Burlew
sb57fury@...
May 30, 2005 12:49 pm
1109
I purchased my motor mounts, frt. and rear, from Kanter. Paul Schmidt ... From: "rob42861" <rjn42861@...> To: <goldenfin@yahoogroups.com> Sent: Monday,...
Paul A. Schmidt
shmitato@...
May 30, 2005 7:54 pm
1110
Paul, Thanks for the info...........Did you get the actual METAL housings, or just the inserts? Thanks, Rob [Non-text portions of this message have been...
Hey guys... I am sure I have known some of you for years. I was here for the very first ForwardLook post. Hello again Big Dave! I have found a 1956 Fury in...
Josh.... If you decide you don't want this car for some reason, please let me know. Also, I would appreciate knowing what others think it is worth. Thanks ...
George McKovich
george@...
Jun 1, 2005 3:31 pm
1115
Here are some photos of it.... What do you think??? Whats it worth and does the engine look stock? http://www.cherrysoda.com/fury Thanks! Josh...
Josh NICE!! I would guess a #3 or a tad less??????? If it 'goes' book value is 10--14K, most of the time things sell above that!! Maybe you could subtract 10%...
The car does not look bad to me at all. All you need to do is have that dent fixed and repaint the car. It looks to me that you probably will not have to do...
Steph Burlew
sb57fury@...
Jun 2, 2005 10:55 pm
1118
Were is the car located ? Steph--- On Wed 06/01, socalsoda < josh@... > wrote: From: socalsoda [mailto: josh@...]To:...
Hello Group I know there was always a question regarding the FP 31 'DOMED PISTONS' that were supposedly put in the FP 31 and created a higher compression...
Ok, I am a Mopar guy once again. I bought the car. Please help me out with the numbers??? BODY# 404.E 2708 VEHICLE# 22296449 What sold me on the car are the...
I think you MUST get the build sheets!! That will answer everything (or most everything) If you need the address,,I can give you that, and it should be in the...
I have the Chrysler Historical address from when I ordered my 1955 Plymouth sheet back in 1998. I planned on doing this but hope to hear if anything can be...
Hi Josh, Congratulations on your purchase! Your low mileage Fury, 38,000 original miles I believe, is genuine! It will also be an adder to our Registry which...
William Lewis
reatawhippets@...
Jun 3, 2005 10:57 pm
1126
Thanks Jack... Also, thanks for the Welcome. I have the engine number at home, I will send it to you. From my Hollander manual it shows that the engine is a...
Good luck with the restoration of the car. It seems that you will not need to do too much socalsoda <josh@...> wrote: Ok, I am a Mopar guy once...
Steph Burlew
sb57fury@...
Jun 4, 2005 5:10 am
1128
Hello Josh: That 56 sounds like a real find!! A couple other numbers things you might check are that when you get time, you can remove the left rear tire...
Bjwt56@...
Jun 4, 2005 9:15 am
1129
Hi Guys, Do any of you know where I can get a pair of INNER rocker panels for a 1956 Fury? I have the outer panels but I also need the INNER panels. Ron...
Ron: If you cannot find inner rocker panels, they are only flat sheet metal and can be easily fabricated by the right body man. I do not recall ever seeing...
Bjwt56@...
Jun 7, 2005 12:55 am
1131
Hello Ron, Great question, so here is the answer for everyone to know. $82.00 each through Autobodyspecialt.com Here is the website link or do a web search...
Ed Dea
ed_dea@...
Jun 7, 2005 5:10 am
1132
HI Y'ALL I AM A NEW MEMBER WHO WISHES HE HAD A FURY. I AM WORKING ON TWO 56 PLYMOUTHS NOW. A 2DR SEDAN AND A HARDTOP. TRY CLASSIC FABRICATION.COM FOR YOUR...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
