so the drive belt goes on in between(on the shaft) the variator(thing with 6 rollers inside) and the outside half of the the drive pulley(the thing that has...
the belt goesint he INSIDE of the variator face and teh fixed face they are both smooth and have an angle on it the outside is teh fixed with the plastic fan...
JL50QT-15 Where is my carbeurator and carbeurator bowl located on my JL50QT-15?? I just purchased this scooter and it was sitting for over a year and had been...
got the belt on...and I think its right....started it up and it seemed all right but when I got to 15-20 mph the scooter boggs down...loses power. Not sure...
yes OH BTW when your looking at the belt MAKE ABSOLUTLY SURE that you put the belt on so that if the front of the bike is on your left and rear tire is on...
Wow! Never heard that before. I'm not saying your wrong, but I have changed a lot of belts and never heard that before. I must have been very lucky to have...
Hi guys, I am new to this group as well as owner to Geely 125cc scooter. I have just adjusted valves clearance. First I set them to 0.12mm and my scoot was...
yea allen I talked to gates and they confermed it that the belts are directional in make, and a few other people told me that as well, and I woudl say your...
Use a dowel or a large screwdriver as a stethescope. Start the bike , put the dowel to your ear and touch it to the engine in various places to determine the...
I never paid attention, but knowing me, I probably (subconciously) put the words so I could read them and that saved my butt! ... are ... and I ... be able to ...
lol good thing I wish I would have done the same thing on my 2nd belt lol I was soo pissed when it broke and i've not gotten a lot of wear out of the chinese...
Did you adjust the clearances with the piston on the compression stroke and at top dead center? ... and ... on. ... than ... maximum. ... unsolved. ... valve...
I just purchased a Hitong Retro X-8 and have two questions for the group. 1. I can't get my high beams to work. The lights don't change from high to low when...
The high beam wire may be unplugged from the back of the switch. You'll have to get in there and check. For the alarm, you'll want to get under the front...
i got a 250cc roadster jmstar.do you know where is the best place to get parts and faster.also i need a repair manula know where yo get one thanks waynep...
Thank you ... From: Allen Grota Date: 07/06/07 22:40:53 To: geelyscooters@yahoogroups.com Subject: [geelyscooters] Re: help Go to www.scootdawg.com or...
Like new under 40km. Ran fine earlier this afternoon. Went to take it to work tonight, went 6 blocks then all of the sudden, like someone hit the kill switch...
make sure that the kill switch isn't shorted to ground, and that as far as I know is an extra wire I have it on my geely as well, headlights dont' work unless...
Also, make sure that the remote starter wasn't the cause. If you started it by the remote, they run 10 minutes and then shut off. It won't restart until you...
Found out where the problem is, took all the body off the darn thing, checked all connections from front tire to rear tire. Finally had life when I wiggled the...
Now that I read your post again, I see you were thinking about putting one on the X1 also...bad idea. You will become too lean. In fact, you might be too...
I read a bad, bad post about Geely's and I just purchased one that was used...... I knew it was going to need some TLC but oh my gosh....... So, my husband ...
Stock it running just fine, not looking to do major changes. ... putting ... fact, ... same ... you ... 50cc, ... and ... in a ... to ... your ... with a ... ...
One of the biggest problems is that people buy things for a few hundred dollars and want them to perform like a 10 thousand dollar machine. Then they treat...
Ahhhh...... gotcha!! So I guess that is a lot like how I am a true believer in Hyundai's even though they don't have great resale!! I had one and loved it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
