... Wrong! A shorter belt will ride lower on the variator. Therefore, you will turn more revs. Short belts will knock a few MPH's off, but you'll get a better...
I think I'm expressing this the wrong way. A belt that is the right length for best average between top speed and accelleration will be at the outer diameter...
Hey robert, Try this. http://www.topbulb.com/about/press/faq.asp Eddie robert <geelyforum@...> wrote: ANY ONE KNOW WHERE I CAN GET SOME YELLOW BULBS...
Swam guy: Try a 670-17.7-30 Fulong I have one that has 1100 miles shows no ware whatso ever--measured width--I did do one thing--Remember the old belt dressing...
I have a 150cc which has about 1306 kmh's and I notice top speed is starting to decline . I read somewhere on the net that if your top speed is falling , the...
Top speed declining could also be an indication of a gummed up carburetor, or stretched throttle cable, or extremely low oil, or... Bill Longyard ... From:...
I have a 2003 Geely QT50JT-21 and I would like to know what the red light below the handlebar mounts means when it's lit. I can't find this in the manuals I...
A 670-17.7-30 Fulong is exactly what I've gone through 4 of in the past 12 months, and 3000 miles. Yours may show no wear, but at 1100 miles I'm betting it is...
I agree Belt Dressing is only a stop gap measure to stop slipping and squeeling till you can get a new belt at your local gas station, remember those? where...
Well, I know that when W.L. speaks, I listen. Gummed up carb can also mean slightly clogged fuel filter or carb jet. Cable you can check easily by seeing if...
Just so you know....yellow tail lights aren't legal in many areas. Get pulled over after a couple beers for yellow tail lights....your screwed. ... TRITON R4...
Hi all, new to the Scooter world, and new to the Geely world. Thanks for having the group for support. So i am having rear brake squeeling on my new 2003...
So i have a bit of drivetrain noise coming from the rear case type area. I dont think this is associated with my worn breaks, it really sounds more like a...
... if ... Oh also I wanted to add-- Is there any other parts, that I will need along with the pads... I.E. common worn, or parts that break during this...
Why do they have an auto petcock in place? Is it a safety / ease of use design? I think mine shuts off now and again, and I am really debating on just putting...
Dear all, I kinda messed up. I was taking the cover off the transmission case of my Geely and there's like 10 aluminium screws all around and I managed to get...
... Go down to your local auto parts store and get an impact driver. You smack it with a hammer and it grips and turns the screw at the same time. I think I...
what I had to do when that happend with mine the first time was use vise grips on it and then replace it. but your best bet is to get a small battery operated...
Yup only thing yellow lights can be used for is turn signels and marker lights Paul ... From: Lee To: geelyscooters@yahoogroups.com Sent: Sunday, October 01,...
There are 2 sections, the CVT and a gear box. The files page on this forum shows details. Some CVT noise is normal, but if it increases suddenly there may be...
****This is an edited version of a previous post**** Quote- Get pulled over after a couple beers for yellow tail lights....your screwed. -Quote And if you're...
Quote- Get pulled over after a couple beers for yellow tail lights....your screwed. -Quote And if you're out riding after a couple of drinks and don't get...
Hello, I avoided talking about the upgrade issue that I had because it is a very awkward and weird situation in which I basically lost my money. I installed...
NO!! don't even drive!! Call a Taxi or a Friend! Paul ... From: dennisdenhartog To: geelyscooters@yahoogroups.com Sent: Monday, October 02, 2006 9:15 AM ...
Pedro you installed the piston WRONG the arrow should be UP to the Intake port! that's why it's all messed up again. Paul ... From: Pedro von Wald To:...
Paul, to be honest I read that arrow on the face of the piston should point towards the exhaust and the two holes on the top of piston should face the intake...
I read that the arro on the face of piston should point towards the exhaustion port; away from the carb. Isn't that right?! Besides the holes on the piston...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
