Hello Gary & all Sorry not to get back sooner. I cannot answer your question at this time, the use of the 1600 engine in each state is to be determined by the...
Daniel and Tracey Jel...
pitlane@...
Mar 5, 2003 10:46 am
896
Hi Danny & All, In my opinion, the Nationals is the pinnacle event on the FV calender. It is the responsibility of the FVAA to support the category as a whole...
Gary, I'll try to stay out of the debate as much as possible but for my two cents worth I don't think that we should run a combined race if it ever came to...
I agree with David unitl 1600's are nation wide there is no point in having a nationals for them. Stephen Butcher ... From: <djcutts@...> To: "fvee...
Stephen Butcher
sb@...
Mar 6, 2003 12:03 am
899
Does anyone have the entry/supp regs to Sandown? I don't think I've made it onto the mailing list yet and can't find an entry on the VMRC website. I would...
Hello all Here at last is the CAMS Bulletin for the Formula Vee Tech Regs as published today by CAMS. These regulations are now in place. There is much...
Daniel and Tracey Jel...
pitlane@...
Mar 6, 2003 9:02 am
901
Got them now. Thanks everyone ... I've ... VMRC...
... The rules are as such if your car has change to suit the requirements you meet the new rules end of story. ChivoOriginal Message ----- From: George ....
Ian Chivas
IJCPLUMB@...
Mar 7, 2003 8:53 am
904
Hi George All of the "new" rules are optional for existing cars (except minimum weight increase), therefore if you comply with existing rules now you won't be...
Andrew Brown
asb1969@...
Mar 7, 2003 8:42 pm
905
Morning all: Question regarding the bolt that has to be glued into the left hand stub axle....which end is it meant to be glued in? i.e. from the outside of...
John & Susi Murphy
murfberg@...
Mar 8, 2003 12:15 am
906
Inserted from the inside. ... From: "John & Susi Murphy" <murfberg@...> To: <fvee@yahoogroups.com> Sent: Saturday, March 08, 2003 11:07 AM Subject: Re:...
Daniel and Tracey Jel...
pitlane@...
Mar 8, 2003 7:11 am
907
The release of the CAMS Bulletin means the regulations now apply. Danny ... From: "Andrew Brown" <asb1969@...> To: <fvee@yahoogroups.com> Sent: Saturday,...
Daniel and Tracey Jel...
pitlane@...
Mar 8, 2003 7:19 am
908
a.. Disc brakes, side impact and upgraded roll over protection is compulsory on new cars first log booked from 01/01/03. Are there any NEW cars out there that...
the bolt would need to be approx 135 mm long which may prove hard to find in 8.8 hi-tensile however, your suggestion makes sense and would not affect the...
John & Susi Murphy
murfberg@...
Mar 8, 2003 10:49 am
910
I don't know if this will be of any help (as the new rules are in place), but here is one way that we are dealing with spindle fatigue cracking in the US: ...
Hi Bob and every one, The rules as they are written require that remanufactured stub axles need to be supplied by the FVAA and bear an FVAA stamp. Rule 2.3(iv)...
Yes there is a supplier for these remanufactured stub axles, it is one of my many to-do things which I hope to finalise in the next week or so and I will ...
Daniel and Tracey Jel...
pitlane@...
Mar 10, 2003 6:45 am
914
Danny, Because of limited production, the new spindles will sell for $125 US each. Volume deals could be possible. Bill Bonow ... From: "Daniel and Tracey...
Hi Guys Can anyone tell me the race gear outlets in Melbourne that sell suits, boots, gloves, steering wheels etc, besides Revolution? Thanks Dean Brandt...
Dean Brandt
dean.brandt@...
Mar 11, 2003 7:09 am
916
Finally got around to uploading a selection (more when I get a minute or two) of images from VMRC Round 1 (Calder Park) Regards, Justin # Justin Deeley...
Thanks Bill Yes I did get some info from Bob Lybarger, he also says that steering arms need to be welded on, what is involved there? We use the standard...
Daniel and Tracey Jel...
pitlane@...
Mar 11, 2003 11:08 am
918
Danny, Don't ask why, but at some point in the US we allowed steering arm to be free. Some use stock, others are cut off and weld on new arms. The new casting...
A few questions and rumors come up as to the requirements of licenses to compete in the 40th at Road America. The most recent 40th committee meeting was last...
Gday All, Could the person who has the PMS stickers please bring some along to Winton this weekend as I need two big ones for my trailer and two smaller ones...
-- What a good idea, can you send some up to Sydney for some of our girls Thanks Bruce ... some along to Winton this weekend as I need two big ones for my ...
Gidday all, at Winton last week I had the bare minimum needed re the LHS stub axle. (75mm Hi Tensile bolt held in by resin). I noticed however that other cars...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
