Hey TEXAS-David, Â Where did you get the electric water pump on the race car? I'm done with the stock pump and want to change it. Most likely will be playing...
it's a davies (australia) that I bought from Pegasus (not the cheapest place - but they always have stuff in stock). I bought the controller, but have stopped...
it's a Davies (from australia) bought from Pegasus (not the cheapest place, but they have stuff in stock). Bought the controller too, but don't use it anymore...
How's things dude? Did the Fiat survive Buttonwillow??? I never heard how the race went on Sunday. I raced on Sunday @ Fontana and was off to the Nationals on...
Just checked, we work after lunch Grp 4 and run Grp 5. Â Â JE... ... From: John Edwards <fiat_nut@...> Subject: [fiat850racing] Hey Mitch, send me a PM...
John, Sorry it has taken so long. Buttonwillow ended well. No other issues with the car. Thanks for the help with the shifter linkage. Ran the same times on...
The 3 vids are up on Youtube (Fontana 10-12-08-1, Fontana 10-12-08-2, Fontana 10-12-08-3). Engine was running with a miss when I took it down to the gas...
Howdy from Costa Mesa,  Just got a call from one of the SCCA SEB (Solo Events Board) members, also a Fiat X1/9 guy, about what can be done to make the...
Howdy one and all, will be going to San Diego's Qualcomm Stadium this weekend w/850 Sedan. My run group is after the lunch break Group 5 and I work in Group...
This link will lead you to this and the other 3 vids... Â http://www.youtube.com/watch?v=DX-UaqkxXeE Â Â Â JE... This link will lead you to this and the...
Check out this video about a 1600cc engine mounted in an 850 Coupe, check the other links for moe info. A fiat engine in a Fiat... WOW! Â BTW, Will have the...
http://www.youtube.com/watch?v=oIInizrFD6o  The fingers move rather slowly this time of night.   http://www.youtube.com/watch?v=oIInizrFD6o The fingers...
JOHN: Neat looking...but (there's always a but)...the most effective way to do the spoiler would be to bring it out to the edge of the fenders...air coming off...
awesome looking but . . . time for ye olde rule book for prepared Solo 2008 version page 112 spoiler may not protrude beyond the bodywork - this may be...
John, Texas Dave et al: I'm building the new race engine for the H-Modified car and find that I don't have any of the locating rings that go between the head...
I don't use them because I don't have any! But then I use the AER studs and tighted the crap out of the nuts so the gasket can't go anywhere. I think it has...
the water outlet is just a block of aluminum that bolts up to the head with another piece of aluminum tube sticking straight up, then curved to accept a hose....
The hollow dowels keep the gasket from moving around and are important if you are using bolts, that said... I usually drill and tap for 7/16 bolts so that I...
Having never worked w/rigid foam insulation before, this was a good excuse to try something a little different. However, making a skateboard ramp was not quite...
Have video from Sunday's Solo event @ AAA Raceway in Fontana and some photos (look under my photos) of the new oil pan that I made for the Sedan all on...
Hello All, I have a wonderful restoration candidate that I sadly need to part with ASAP. It is a 1970 Sport Spider that was found after sitting in a garage...
JOHN: I assume the flywheel is supposed to fit snugly on the end of the crankshaft on an 850, because that's how it seems to come from the factory. Or do the...
I have trouble believing it was a misalignment that broke the bolts - but I can't see what you have. A misalignment would more likely wallow out the input...
Hi Jeff... I'm with the Texan...If you had misalignment, HOW did you get the pilot shaft and bearing to fit together ??? or did you force the trans and engine...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
