I have an 89 4-spd carb model in charcoal grey (I think it's black, but...) up here in Mn. for sale. Rust free from Idaho. $1600 and drive it home. Brenton ...
Thanks, but 89 carb not on my list, when I posted I forgot to add 1991 to 1993, manual only, fuel injection. My fault,I need to correct post. But, thank you...
I HAVE A 93 FESTIVA L AND IT WONT START. I CHANGED THE BATTERY AND STILL NOTHIN THE INTERIOR NOTHING WORKS THE EXTERIOR THE ONLY THING THAT WORKS ARE THE...
Check the fusable link wires between the left headlight and the left strut tower. cjacks29 <cjacks29@...> wrote: I HAVE A 93 FESTIVA L AND IT WONT START....
Middle fusible link! ... From: waxhawdon <waxhawdon@...> Check the fusable link wires between the left headlight and the left strut tower. cjacks29...
TurboFource@...
Jan 13, 2008 5:07 pm
42898
You've lost the Main fusible link (middle link in the bank of three links mounted on the strut tower, drivers side -- they look like 3 small loops of wire). Go...
Thanks, I actually replaced the fusible links earlier today and it fixed the problem. Thanks for your time. ... left strut tower. ... POWER ... BUT ... GROUND ...
Heres' a GOOD one. A MONTH ago I replaced ALL the brakes-front + back. I go thru inspection last Sat and it FAILS for the REAR brakes. According to the...
turn the drum maybe... ... From: Rob To: festiva@yahoogroups.com Sent: Monday, January 14, 2008 6:35 AM Subject: [festiva] Brakes Heres' a GOOD one. A MONTH...
The rear brakes are adjusted by using the ebrake. There is a notched paw inside that is pulled back when the ebrake is used. This ratchets a lever out and...
I would look at two things.. 1) is the pivot adjuster seized (as they always seem to be) which can be freed by peening the rivet slightly and lubricating it...
Hello all, What's the easiest way to remove the steering column lock on a Festiva, preferably without power tools I've got the steering wheel off along with...
Hello Ian, I just saw your clear turn signal lenses on you car on CarDomain. Are those from a different car altogether or from a Japanese Mazda 121?...
I found a latch switch & wire and installed it onto my hatch latch. There is a little copper (?) protrusion that looks as if it needs to make contact with...
They are attached by 2 break off bolts from the lower side. The head that you see is what is left behind after the proper torque was reached, and the bolt...
Ah! I was going to try to locate the reverse lenses from an early 90's Dodge Colt. From memory, they seemed to be the same dimensions. ... Mazda B2000 truck....
All: Has anyone ever had problems getting the half shafts back in? This is the second time I've done this job and I just can't get the splines past where the...
I believe that was covered long ago, and IIRC it is that some replacement shafts cilps are not tapered on the edges like the OE were. The square edged clips...
... Well, it is solved now. I just hit the stub axle once with a large ball peen hammer and it slid in. One problem I was having was the steering nuckle was...
Am I correct in guessing the Festy has a protective cover mounted over the tank? Just FOUR corner bolts hold it in place?? OR is this the TANK itself?? Thanx ...
That is just a cover plate that you may use to access your fuel sending unit. HTH Michael Rob <robm1701d@...> wrote: Am I correct in guessing the Festy has...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
