Or possibly a head gasket breach....and that you dont want but then again the B3 is probably an easy one repair... Festiva Guy <festivaguy@...> wrote:...
You would likely just need to strip the intake and exhaust manifolds and move them to the carb engine, acc items like the alternator, if your car has the later...
We just had that on a 92 auto car, and it was a thermostat that needed changed. The belt problem is what still bothers me. That has gone on TOO LONG, and I...
I recently go Bendix Rotors from Roger (Festiva Mortorsport) for $23. I took the knuckles to a machine shop new bearings and seals pressed in and have the new...
Jess, Where are you from there are a couple in a junkyard here in WI I could grab one from if you cant find one. It would prolly cost me about 40 to get it. If...
Try emailing Dean @ trucksigns@... He wrote in a couple of times saying he was parting out over 30 FESTIES I never followed up to see if he was bogus or not...
... No, I hadn't... but I checked it last night and that was the problem! D'oh! I think I might have a leak, although there were no puddles and I've been ...
having low coolant is bad. real bad. Anyway, without consistent coolant flowing past the temp sensor, the ecu will see constantly changing voltage, causing the...
Hi Folks, Dean is a good guy. I have bought from him a couple of times. No worries! Bill Venia 92 GL 93L 97 Aspire ... [Non-text portions of this message have...
I agree a 323 1.6L SOHC "B6" is plug and play just pop out the B3 and its ECU and plug in a B6 and its stock ecu......way less work and you must consider that...
i would like to have new rotors put on my 89 festy as well. according to the childens manual the rotors are pressed on and need to be taken off by a...
I should have been more expliciate about why you may need a new oil pan. I have replaced two that just rotted away here in the salty northeast. Also it takes...
Two days ago it was -5 in the morning when I headed out after a 10 minute warmup. The temp gauge read normal but only stone cold air came from the heater. I...
Reason being the car has a bad motor & the motor i have is carberated i just thought why not use them & put 2&2 together.If i swap intakes & exhaustmanifolds...
WEFOSTERSLUVNC@...
Mar 2, 2006 2:04 pm
39467
I"m not worried about speed just relyability to work and home thats all .thanks to all for this nice group of helping people. [Non-text portions of this...
WEFOSTERSLUVNC@...
Mar 2, 2006 2:06 pm
39468
Last 2 times for me, the ignition module popped. Try a spare dist if possible. I keep 2 extras because of that. About 175.00 for a rebuild at Advance, or find ...
... Terry, The machine shop here charges $25 each front wheel to press in the new bearing and seals and attach the new rotors. Jess ... according to the...
I'm about to replace my 1989 Festiva (a little over 113,000 miles) with a 1999 Nissan Maxima SE. The Festiva will be 17 in April and she's been through a lot...
You're welcome...hope all goes well. If you take the knuckles to a machine shop, make sure they have the specs on the Festiva preload spacer (goes between the...
these motors are getting harder to find in good condition. ... signature test'; "> __________________________________________________ Do You Yahoo!? Tired of...
i have limited cash & already have this spare motor & a car with a bad motor i figure why not i dont care about speed i just want to turn key & go from work...
WEFOSTERSLUVNC@...
Mar 5, 2006 2:36 pm
39477
I have a 89 festiva with a bad oil leak coming from the pan.My ? is how do you know weather it is coming from the pan or crankshaft seal? If it is seal and I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
