You use a scuff pad and go over the bumper a few times. Then you use a grease and wax remover and clean the bumper really good. Finally you prep the bumper...
Hey guys I wanted to ask a question about maximum front wheel and tired widths and talk about autox tires. I've been browsing around for a front set of autox...
Are you wanting to use the 7" wheels front and back, or just on the front? If yes, I'll tell you what I know. The rear fitment is actually more important, as...
Yes id only like to use this combo on the front of the car. I just cant seem to figure out what the offset should be on a wheel this wide. I looked up some...
Steve, yes, the Subaru Justy seatbelt colors were identical to the originals in my '88 LX. Same part, entirely, as best I could tell. Thanks for the advice...
Do you have the Aspire front brakes, or Festiva? Stevo ... just cant seem to figure out what the offset should be on a wheel this wide. I looked up some...
I basically did this to my 88 before I swapped to the 16v engine, I'd say maybe 17 flat or above. I made my own adapter, and used a new Holley 5200 carb, with...
i noticed the tracer has about 10 less hp and 2 less pounds of trq......so is this really a noticeable difference and whats the big difference among the 2...
I currently have festiva front brakes but I will be swapping to the aspire front brakes very soon so ill be ordering these wheels in the 4x100 bolt pattern. ...
I'm tring to replace the output seals on a 97 aspire w/5 speed manual. Well i'm at the step to take them out and in the Haynes manual it just says to pry them...
There is a tool which you can attach to the axle that allows you to use a slide hammer. Check with your local McParts place. They usually lend tools for...
This usually works, but the last time I pulled the driverside axle out, the circlip broke that holds the inner tripod together, and I ended up with the outer...
They can sometimes be a bitch to get out man. Pry like you have never pried before and they will eventually pop out. Maybe while some one has a screwdriver...
Will the tranny case withstand the applied forces of a puller? I wasn´t able to remove the driver´s side shaft of one of my donor b3s, yet -christian- ... ...
no the tranny case cannot withstand the force of the puller lol i have already broken 1 with a puller i would not suggest a puller christian leiteritz...
The puller is what Ford recommends to get the shaft out, I cannot see how using a slide hammer type puller would damage the transmission case more than using...
well man if i had a scanner i could show you the pics of my tranny casing after we gave 2 good yanks of the puller lol. bye the way has anyone had a problem...
... Unfortunately, this does sometimes happen, although it appears to be a problem only with the aftermarket axles. I have never heard of anyone breaking a...
hey stevo, we've talked and you know i'm no mechanic,machinist yes,when i hear the term puller,to an old country boy,there are 2 kinds i think of, a gear...
hey stevo, we've talked and you know i'm no mechanic,machinist yes,when i hear the term puller,to an old country boy,there are 2 kinds i think of, a gear...
... my acts like it's got a bad wire connection but i've checked all the wires fuses and everything else i can see and i dont see a problem. ... fix the...
The type I believe that is recommended is the slide hammer type. The gear puller type could be bad if the circlip binded in the differential, as they can...
... You know, at the junk yard the Aspire axles that I took for my Festiva came out very easily. Maybe someone upstairs was just helping me out becuase when I...
I just want to thank everyone for their help. I tried everything everyone said and still nothing. So I decided to take the cables off the starter to clean...
what is the least expensive car in the world? and where is it? is it of any quality? robby _________________________________________________________________ ...
I have an '88 Festiva LX and overall, it has given me excellent, troublefree service with one exception. The ignitions system developed a serious problem, and...
Bill, While not what you'd necessarily consider a real performance piece, the factory distributor is a pretty good unit. I think you have discovered one of...
check the carburator for flat spots by revving it up in neutral slowly, could be the problem I had an 89 that had a carb that froze one winter while driving,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
