... This is of interest.... Is there an address I can er... address to see a stock list? Sounds like a fine peice of lurking. Royce...
Royce Creasey
royce@...
Aug 1, 2005 7:31 am
31207
... The metal must be *clean*. Grinding through to fresh bright steel helps, too. Once you're experienced you can weld almost anything, but clean metal is...
... He's right you know. Bear in mind the fire hazard all those little pieces of glowing metal present. All those oily rags, old gaskets and bits of...
Royce Creasey
royce@...
Aug 1, 2005 12:47 pm
31209
snip ... Those automatic darkening masks help a lot too. Even a cheap one is much easier to use than a permanently dark mask. Arthur....
... So THAT's my problem - I thought I was just untidy, but it turns out my problem is not owning a welder. Huge relief! But now I'm worried that if I do buy...
I finally decided I had too many buckets of small pieces of metal almost big enough to save, and so my garbage can has been pretty heavy the last couple of...
snip ... Has anyone considered bulding an engine for FF use. I don't mean from scratch- rather get a doner engine and build a new block to re-arrange those...
snip ... What are the requirement when getting a shed if you plan to weld in it? Fire proofing - veltilation , screens, earthing / electrocution etc? Peter ...
... Strangely enough we did - around this time last year. Search on Yahoo for posts on 'Crankcases and designs' (Starting around post number #22199) I'll have...
... Nobody has belled the cat then ... Peter __________________________________ Yahoo! Mail for Mobile Take Yahoo! Mail with you! Check email on your mobile...
<<I'll have a GSXR/R1/Fireblade motor in the Voyager longitudinal layout please!>> http://www.motoczysz.com/images/tech/engine_photo.jpg Like the Moto Czysz?...
On 31/7/05 10:58 am, "feet_forward@yahoogroups.com" ... I beg to differ. Arthur's always going on about the problems of balancing a tele-forked FF at slow...
Paul Blezard
paulblez@...
Aug 1, 2005 5:43 pm
31218
I like the sound of the "could be the largest collection of Quasars ever assembled in one place". Keep those entries coming. Don't forget to bring proof of...
snip ... I am pretty much as far forward as I can get. Bias with me sitting on it is 45% front to 55% rear. This is about the same as the GPZFF with the road ...
... snip ... What is the rake of the TMAX? I didn't have any big problem with it either, sans tail, but with WIDE bars. What is the new bar length (pivot to...
... Oops! Gave the game away there. I must write to the council and apologise for all the rough roads I was virtually experiencing on my lowered Bananaskin!...
... You are very kind, but the problem centres around wife insisting we attend a wedding on Saturday (not our own I hasten to add) and her complete inability...
... wrote: At the very least you'll have a ... appreciate ... And do not worry if one of those red hot globules goes in your eye by jumping over your mask, as...
... REPLY: Well, yes, I see no reason why not. My thought was that cabin FFs and open ones have different advantages and limitations: open designs can be...
An interesting line of thought... How about whipping out the Burgman engine and CVT, dropping in a few batteries, adding one of those clever in-wheel drive...
Hello all ... What are the requirement when getting a shed if you plan to weld in it? Fire proofing - veltilation, screens, earthing / electrocution etc? <<< ...
Last weekend (July 23/24) I took the Quasar back to the sunny South East coast for its long-awaited refurbishment courtesy of John Crowson (Mark¹s brother)...
Paul Blezard
paulblez@...
Aug 2, 2005 3:43 am
31228
... Soundproofing. Tends to ned to be built in unlike most of the other qualities. You'll be making horrible noises with the angle grinder you clean up the...
Royce Creasey
royce@...
Aug 2, 2005 7:14 am
31229
... I think I was trying to suggest that if they didn't exist and you came up with a motorcycle now you'd get arrested.... Royce...
Royce Creasey
royce@...
Aug 2, 2005 7:15 am
31230
The C Max will go to as good as 0 before I need to put mee feet down. When setting off as soon as the engine is revved to set off feet can be up. VT500 was the...
Now I have got a proper www address, please let me know any links you would like adding to mee web page. Page has not been updated on content yet, but some of...
... (snip..) I think that Arthurs point is that tele's impose limitations on control at some part of the speed range - as a function of the high geometry ...
Royce Creasey
royce@...
Aug 2, 2005 8:54 am
31233
Bob Wreford <bobwreford@...> Mon, 1 Aug 2005 18:51:31 ... It seems to have had some effect on your diet as well. You've put on weight round the...
... You could use ear defenders... I imagine the neighbours will complain when you are grinding welds at 11pm. Regarding setting the place on fire, it is very...
I now do my welding and grinding outside the garage. After setting the Metro on fire whilst chopping it up right in front of the garage I'm a bit more...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
