Does anyone know where to find an inlet receptacle that could be
installed in a bumper (like on Felix's car) or perhaps one that works
above the license plate? I'm having trouble finding one that has some
type of rubber cap for it.
Thanks,
Chris
-----------------------------------------------------------
EAA-PHEV website at http://www.eaa-phev.org
If you wish to unsubscribe from this mailing, send mail to list2006@... with a subject of: unsubscribe eaa-phev
Does anyone know where to find an inlet receptacle that could be installed in a bumper (like on Felix's car) or perhaps one that works above the license plate?...
Chris Ewert
chris@...
May 4, 2007 2:24 pm
I don't know but I will want that type too. Although, I have though about mounting a retractable cord under the care behind the bumper to save cargo space. ...
Philippi, James
james.philippi@...
May 4, 2007 2:35 pm
How about something used in marine applications? If not the following, then something similar? It does seem a bit bulky. I searched for power inlet on ebay...
Bill Lin
williamslin.wsl@...
May 4, 2007 2:57 pm
... From: "Chris Ewert" <chris@...> To: <eaa-phev@...> Sent: Friday, May 04, 2007 7:23 AM Subject: [eaa-phev] Bumper Inlet Receptacle ... ...
michael brogan
mikeb@...
May 4, 2007 2:53 pm
Not exacly for a bumper, but I got one at an RV (motorhome) parts store. Look on line for camping equipment. Steve ... ...
Steve Powers
eaa-phev@...
May 4, 2007 3:20 pm
WEST Marine is also a good place to look. I have seen a couple shore power plugs that would work. They also have the correct weather proofing. John ... From:...
John Skier
jskier@...
May 4, 2007 3:23 pm
The Hubbell part # is 5278-C for the straight blade, Hubbell part # is 4716-C for the twist lock. Most other suppliers use some variation of hubbells part...
David W. Kennington
dkennington@...
May 4, 2007 4:10 pm
I'm using a Marinco shore power 50Amp/230V recepticle with a cover. Installed this in the front of the car adjacent to the pass side fog light. Works like a...
roly 77 calv
cenyinc@...
May 4, 2007 3:29 pm
Hi all - This is the receptacle we used to do our Prius PHEV conversion. http://www.marinco.com/scpt/ProdPage.php?loadItem=200BBI.RV_ParkPower%20Recreational ...
John Dailey
eaa-phev@...
May 4, 2007 3:36 pm
Hi all - Oops. My last message linked to the info for a straight blade receptacle. We actually used a twist-lock version very similar to the one shown in the ...
John Dailey
eaa-phev@...
May 4, 2007 3:38 pm
Return Receipt Your Re: [eaa-phev] Bumper Inlet Receptacle document: was David W. Kennington/US/NA/TCCC received by: at: 05/04/2007...
David W. Kennington
dkennington@...
May 4, 2007 4:10 pm
Part 2 of my answer, this one includes pictures of my install. These Marinco hardware comes in 15, 20, 30 & 50 Amps flavors with combination of 110/220, 2 and...
CENY (CORPORATE)
cenyinc@...
May 6, 2007 1:47 am
2 options I found, the top is an inexpensive straight blade, the bottom is a fancier twist lock. Either is available from any electrical supply. ...
David W. Kennington
dkennington@...
May 7, 2007 12:58 pm
Part 2 of my answer, this one includes pictures of my install. These Marinco hardware comes in 15, 20, 30 & 50 Amps flavors with combination of 110/220, 2 and...
CENY (CORPORATE)
cenyinc@...
May 6, 2007 1:48 am
Hey Plug in folks we just used the twist lock 3 pin with grounded shield for the Green cars 50 amp 125/250 volt inlet. This is the industrial spider box type...
Send Email