Hi, i need some info about 1G eprom ecus. Hope somebody can help me on this. It's just two questions. 1- An ECU from an automatic transmission car does work on...
... Yes, an automatic ECU just differs in the software from a manual ECU. Once you change the chip it becomes identical. ... EA01 is from the 1993 model year...
Does anyone have an eprom ecu for sale. This would be going in a 92 talon. I'm kind of strapped for cash, but maybe we can work out some kind of trade, i have...
Hi everyone, is the first time I post here, but long time reading. I am doing a turbo conversion and the ecu rom is E770a labeled. Does anyone has the fuel...
Just wanted to say thanks for all of your alls hard work do with dsm chipping. Also Jeff i bought a chip from you for my friends 2g and before it ran like crap...
Hi all I have a problem with my 4G63 NT 2.0 Eclipse and I thought you may be able to help. The car is eating 98 petrol like crazy, almost as it would be...
... Are you sure it isn't something simple like a bad sparkplug wire? Once a cylinder isn't firing, the feedback loop of the ECU can get screwed up in strange...
The other thing you might want to consider is simply using the turbo ECU code, like our E931. The NT maps are usually scaled for MUCH less airflow, so you will...
The motor is 7bolt 4G63 non turbo at the moment and I would like to adjust the timing and fueling with this motor, and if everything is right install the new...
You can email it to me at keydiver@... and I'll post it in the Files section. But, as I said, you might want to consider trying the E931 code in your car...
I´m thinking to use it as you indicate me but I have seen diferences between both main boards and I don´t know if it would be any incompatibility. I can see...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the dsm-ecu group. File : /Other Code...
dsm-ecu@yahoogroups.com
Feb 6, 2008 3:31 pm
6730
It appears that in the E770A.BIN you gave me, these are the addresses I have found so far: 1943 (D943) - Global Fuel - 7Ah = 240cc @ 49psi 3C7D (FC7D) -...
I have tried programming a (European)colt GTI ecu with the E931 code and can confirm that it works. I had the ecu plugged into a '90 eagle Talon Tsi and the...
Hey I'm interested in tuning my DSM with TunerPro, and I kind of get the gist of how things work, I open the ecu, pull out the chip, flash a new tune to it and...
Hi dutch_dsm! There are hardware differenties between the nt and t ecus, but you can convert it if you have one for turbo. (I did some from EDM NT Eclipse,...
Hi dutch_dsm! There are hardware differenties between the nt and t ecus, but you can convert it if you have one for turbo. (I did some from EDM NT Eclipse,...
... Basically if you don't have an ECU with Eprom chip you can't do anything. Read this, it's from dsmlink but it's the same case if you want to use tunerpro: ...
Hi.. Does anyone knows how to remove or increase the speed limiter? On the standard mitsubishi ecu, speed has been set to cut at 180km/h. How to remove or...
Hi, I'm having a problem with an ECU generating a knock code. The car is a converted to turbo 2wd Galant using an Eclipse ECU (EA01 code). I'm getting the...
... Could simply be floating. Try connecting a 10k ohm resistor from that input pin to ground, and then measure again. However, if you've tried several...
Last night we went a tested a ecu in a 1g eclipse and found that we where getting 10volts. This ecu works as well, and gives no check engine light etc. ... I...
Yes, there is some bias voltage to the sensor. I believe that is how it tests for an open circuit issue, so it is normal. Have you tried a different ECU? How...
It would help if you knew what code you are working with. I have removed the speed limiter on dozens of JDM ECU's. Open the ECU and get the EPROM number, like...
I've done this for quite a few guys who run without an O2 sensor, or want to run open-loop all the time, with a MAFT pro for example. All the code between...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
