Someone asked about anti-lag code and it sparked my interest. Found some code in a thread from back in 2004. Message #1872 Re: Retarding timing on the...
I'm having trouble checking the base timing on my '97 gs-t with '95 eprom ecu (keydiver chip). At iddle i get unstable timing advance (7-15º) so i can't...
Pin 52 is the Ignition Timing Adjustment wire. Should be white. If it isn't in the 97's harness you could add it. See http://www.vfaq.com for setting base...
Hi Does anyone has the fuel maps locations of this ROM..This veicule only exist in Europe and Australia..I need to change the fuel and ignition maps to run...
Hey, thanks a lot Ceddy!!! I'll try that. About ISC and iddle setting, i think pin #56 (or pin# on OBD-II connector) is the one i should ground. thanks for...
Anybody know about this ECU - it is a single board ECU, the chip says EC64, supposedly from a VR-4. The case says MD128618 E2T34572. I have seen mention made...
Yes, the MD128618 was an older dual-board ECU from a VR-4, but I guess its possible that Mitsu could have manufactured a newer single-board replacement. Post...
Hi, is there any vaulve that shows me where exactly my ecu is in my timingmap(/fuelmap) right now? So is it possible to log that? That would be very usefull...
I'm sure there's an eaiser way to do it, but I used MMCD to look at RPM and Timing advance and match up the load point on the maps. If you have knock, you're...
My method, after implementing the double-width maps, was to log the load number itself by putting it in the logger table in place of the two-byte airflow...
Try Pocket Dyno. You can download it from the files section of dsm-ecu yahoo homepage, see the links at the bottom of the page. It's simple to use, there's...
Hi, brand new to the board and the Ostrich tuning. I've managed to tune my car fairly well so far. Played with Winhex and Tuner pro, but can't seem to find the...
You are right about the search... somethings screwed in Yahoo methinks.. Anyway, checkout post 5333 - i thinks its the last post on the subject. Cheers, John...
Thanks for that, I ran across that last night when I was searching agian. That doesn't make too much sense to me at the moment. I've been running through the...
Sorry to semi Hijack this, ive been trying to do this for E952 rom for a while, but it seems I cant find any similar code in it (comparing to E931) Anyone have...
There is code listed in the replies before the linked reply in that same topic. This is my knock gauge code, taken from some post here when search worked. I...
The gauge code is in almost the same address as an E931, right around 5F08 according to my notes. Knocksum is address 89 instead of 8B, so you need to take...
Thank you very much for this, it's actully starting to make sense now that I can compare what the changes are actually doing. And now I also see where the code...
Standard place in code where Boost Gauge value is updated is too slow for showing knocks. I made modifications in Christian commented source in place where...
Ok that went straight over my head. Where is that code writen to? And what programs do you use to modify it? Really just starting out here, this is way over my...
Hello everyone. I just joined up so I could start doing some research on a project I may be undertaking, and I've noticed the search seems to be busted. Am I...
You don't want to control location in the compiled code because it is changing with mods of source code. You can make mods that don't change compailed...
Most code you'll find on these boards is instructions on what to change in the .bin with a hex editor. This just involves changing numbers in the file. What he...
Hi all, Going back through the archives I found the bits and pieces needed to attempt a cyclone intake and water injection by manipulating these solenoids. i.e...
Reading back through the archives I found the bits on Lean Burn. Several times Jeff has mentioned that if it is to be used the high fuel trim (HFT) must be...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
