Just some misc data points to post while the GVR4 is down again [don't ask]. From my logging, timing definitely makes a difference in torque (load) while AFR...
OK, so what exactly is load? Is it an airflow value, or dyno value, or ??? Are you sure that your torque is proportional to your load numbers? It looks to...
Carl, ... Ecu map load row (g/rev) on double-range maps. ... Everything I've seen in data, calculations and read on this list seems to support that assumption....
OK, I thought maybe you were talking about actual measured engine output in some form. I realize that the air mass/rev is generally tied to torque, but it...
I've been doing a little research today on changing the baud rate to something a little more useful/standard. It has to be within 5% +/- of your target baud...
Take a look at the parameters for the 6801 SCI (link below) in table 6, page 3-116 and use a frequency of E=2MHz (4f0=8MHz), you should get the baud rate given...
Thank you, now I understand it's working more/less in stock form. Am I correct now in thinking that, unless you changed the crystal speed, going to another set...
the J&S has an adjustable sensitivity. I set it at ten PSI and drove the hell out of it to find the threshold. It is set very conservative. I usually run 17...
So I was going to use the evap solenoid to activate my Nitrous controller. I wrote some code to hopefully make it activate on when its safe. This is my only...
Ok, wow... now I remember why I did CIS instead of CS :-) So my code works right up until I add the speed sensor check to my code, I have no idea why its not...
You are checking the clutchswitch bit wrong. You need to use either: 87 06 20 XX or 8F 06 20 XX to test the bit, and jump ahead XX bytes depending whether it...
Hmm, well I used the code exactly liek it is but added parts to it as I tested. Worked fine with only the clutch check. Worked fine with clutch and throttle. ...
I've been messing with TunerPro and doing a few things here and there. These are the settings i've came up with so far. I was wondering if these are alright...
http://www.labattz.com/phpBB2/viewtopic.php?t=11843&postdays=0&postorder=asc&highlight=tunerpro&start=0 I found that bit of code, I came back here and was...
... http://www.labattz.com/phpBB2/viewtopic.php?t=11843&postdays=0&postorder=asc&highlight=tunerpro&start=0 ... I found the code in message #3267 It's from...
i dont know where to find the full info, but ive tried some code that was posted to support the 5v wb input. i would have to locate the info ive got since it...
Sorry to bring a thread up from the dead, but anyone have a more recent version of code or input on how this is working out? Seince this was posted back on 04...
... that was ... ive got ... with an ... Hopefully someone's got the full info. Does this simply require a wideband sensor, or does it also need the electronic...
... You MUST have the WBO2 box, period. Replace the stock NBO2 signal to the ecu with the WBO2 box wideband 0-5v output. ... See previously mentioned msg#...
Hey guys, I just got a 1993 Dodge Stealth Twin Turbo, and given that it is 13 years old, it needs a little tweaking. In particular, the turbo impellers are...
Do you have a photo of the PCB? ... be ... upgrades ... Given ... flange, ... turbo on ... utterly ... ms/bit ... injectors. ... the ... working on ... ECUs?...
Very few people play with the 3000GT/Stealth code, due to the inaccessability of the ROM code (it doesn't have an EPROM like the DSM ECU's). There are a few...
Hi everyone, I just joined this group in hopes of learning more on the DSM ECU's. My name is Dan. I have finally flip on DSM's I currently own 2 a 1990...
Hey, Dennis, Welcome. Jeff Summed it up well. There are a few high- priced uptions, but I have not seen any of thse custom ECUs anywhere. Most anyone serious...
A friend of mine wants a 2g chip. I did a bit of searching and didint find too much useful. I'm looking for XDF file or something simular I can throw in...
I just bought this burner http://www.moates.net/burn1-flashnburn-usbbased-chip-programmer-p-48.html I know it will work with 1g's, and tunerpro wich is pretty...
... http://www.moates.net/burn1-flashnburn-usbbased-chip-programmer-p-48.html ... I found out It's capable of burning these chips: Read/Write - 29C256, 29F040,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
