Jarrod, I think you will find in the files section under "other ecu's" maybe, the factory 8618 roms from my ecu. I also have somewhere, on a harddrive, most of...
I believe the table at $FEA7 is the basic coil energization time (dwell) as a function of battery voltage (in 64usec units). The ECU makes adjustment on top of...
Thanks Andrew, I have found alot of ROM's that are only 16K on the file server. The ROM that I have copied from the ECU that I am using is the 32K file. If...
I believe I saw an 8618 image at this group's file database. Please check it out. ... From: Jarad To: dsm-ecu@yahoogroups.com Sent: Monday, May 01, 2006 6:56...
I think you will find that all 8618 ecus came with E657 rom. Chances are, your 32kb rom is just from a 32kb chip, the first 16kb will contain no data. The...
Sorry.. reviving a very old thread here.. I am using pudhed's knock gauge code for my gvr4. From experiments, I found that the following table/gauge scale...
hey there firts of all thx for all the "experiment", research and other possible thing u guys have done here. now what i post for. PLZ help me understant...
... It sounds like you might be in a bit over your head on that one, unless Nick has taken steps to make it very user-friendly. Last I knew it required the...
first thx for the quick answer now can u be more specific has in what sensors or what # item i have to buy from ramchargers.com and the palm thing u talk about...
... can u be a bit more specif has to what item i have to buy from ramchargers and "palm" u mean a datalogger? what sofware would i need? and what is the bin...
... You're in over your head. Just buy a MAFT-Pro if you want to go speed density. Nick hasn't even released this in a form that most of the regulars here...
I'm going to attempt to test in in #1886, as I've had people ask me if I'll send them a copy of it. From what Nick says, most people using it are using the...
... if ... it ... What about 2,5 bar sensor (Motorola mpx4250a - 250kpascal absolute pressure, 0-5v output) connected to EGRT ? I can log pressure with MMCD ...
I have been lurking on here for a little while, trying to take in a bunch of info for when I FINALLY find my eprom ecu. I have a 90 gsx and just recently...
im not trying to be a dick or anything, but you should pick up the info that youve gathered and build your own xdf. it will most probably help you to ...
Hi all, I found this eprom id from the eclipse 2.0l turbo ecu MD154076. Have anyone worked on this eprom? Are they the same as E931 ? I just want to know that...
Hi all I just installed a PLX-250 wideband sensor and gauge. I specifically remember a post using MMcD logging a wide band with a 0-5 volt output. But I...
Would the GM 2 bar Map sensor work ok with Nicks speed density conversion program? Or do somethings inside the chip need to be changed for it to work properly?...
I modded an E800 once for a guy from Oman. It is pretty much identical to an E931, except most of the memory addresses are different, and the code addresses...
Thanks jeff. That's all I need to confirm because sometime the eprom dies out during the extracting/socketing process. Should that happens, I don't have any...
If You have sensor witch 0-5v output, You should connect it to EGRT input. This input is used in MMCD as a wide band too (normaly EGRT, also pressure 3bar or...
In a message dated 5/7/2006 10:55:10 P.M. Eastern Daylight Time, papa@... writes: If You have sensor witch 0-5v output, You should connect it to EGRT ...
I understand selecting it under the preferences. What I am asking is what pin does the 0-5 volt output wire go too? In a message dated 5/8/2006 5:33:52 P.M....
the egrt input is ecu pin 15. it should be blue with a yellow stripe, all of mine were and the factory service manual backs me up, had to double check. there...
It should be pin 15 on ECU as written in http://www.vfaq.com/mods/ecu- harness-1G.html. But I have connected MAP to EGRT connector near the engine. ... is...
... the ... Well guys, I just bought one of these harnesses from FullThrottle, and its PERFECT. It connects the GM IAT and MAP sensor to the proper wires on...
So are you going to work out a deal with Nick to add this to your chips? :-) I'd like to put the feature into standard E931 code with a corresponding TunerPro...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
