Which is the best table to edit for smog (CA smog sucks)? Smog is done at idle and at 2K rpm. Should i just adjust all the tables at the specific rpm points?...
Your system should already be optimized to pass smog. It just needs to run in closed loop with a correctly functioning O2 sensor. If you're running in open...
Does the 27SF512 chip for the 2G have to be 70ns, or 120ns, or what would be the correct one to get? Same for the 29C256 chip in the 1G? Als, these are the...
Thanks Mark! ;) I thgink I'm going to go with the 70ns on both. I can find the 27SF512 with no problem, but the 29C256 is being a bit unfriendly. No place ...
hi everyone im looking to fix my datalogging cable, someone broke into my car a couple weeks ago and decided to rip my cable in half. does anyone know where i...
What I did was run a 559K ohm resistor on the signal wire to the knock sensor to ground. the ECU reads zero knock at all times. You can then use headphones or...
Has anyone else noticed that the intake air temperature sensors in the stock MAF seem to heatsoak? It also seems somewhat difficult to get the temps down even...
with all of the limitations of the stock MAF I went with a MAFT and a 3" GM MAS. The biggest thing I had a problem with was mounting an air filter on the stock...
Folks, I've got a guy here that has the following: 1991 mistu eclipse awd 4g63 turbo What does he need to do in terms of editor / definition / chipping? What...
Craig, First a question for you...have you considered offering a basic DSM ECU tuneup kit? In other words, a socket, a 29C256, and the three capacitors in a...
Craig: here's what I use. I use hexedit to edit the raw .bin file things like IPW cap, knock code mods, and the maf comp table.. I also use evilscribe to edit...
Couldnt help to notice you have the deadtime listed at 300 for the 680cc pte/delphi injectors.. I currently have mine set to 210 on dsmlink, do you guys...
Running dsmlink with 680cc pte/delphi injectors, 210lph rx7 pump re- wired, stock fpr, with an inj dead time set to 210... I just seen the guide on here says...
The deadtime will primarily affect your LOW TRIM, so adjust the deadtime as necessary to get all the trims roughly equal. Usually, I still see the LOW TRIM...
i'm using the ostrich and also have a programmer i bought from moates, along with tunerpro rt (registered) and have no serious problems. with some help from...
Very usefull information, appreciate it Jeff! -Tom ... From: Jeff Oberholtzer To: dsm-ecu@yahoogroups.com Sent: Monday, November 14, 2005 10:42 AM Subject:...
I picked up a nicely modded GVR4 about a month ago. It came with an HKS EVC and a real TMO stage III chip. I've been noticing that there's a nasty lean spot...
The TMO chip has the code shifted around. It is a little more time consuming to edit the TMO chip with the findings on this forum, but it is easily doable if...
... If it's a TMO chip with selectable stutter it might be worth the time to find the correct code locations and make the changes to it. If it's for the GVR4...
I'm currently still tweaking my TMO image, but if I were starting right now I'd avoid that. I'd just sell the TMO chip for whatever I could get for it and...
Hello! Sorry for delay, so much works. Unfortunately, upload ROM from 6111 is very complex. For reading ROM the additional equipment and the software is...
... Andrew Hello Andrew: I like to replace some damage MH6111, I mean to write the original ROM dump in the new one MH6111, I have been looking for datasheets ...
i would like to get a stock .bin file for my car to start modifying. If anyone has one, you can email it to jwarren269@... or if anyone has a link to a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
