Much of the internal maps and functionality are explained in Cobb and EcuTEK's forums, but I think everyone who knows how to actually flash or download images...
Okay, here's what I found that works, and I'm posting this information for anyone who (tries in vain with this Y-group interface) to search for this same issue...
... the ... only ... octane map ... basically ... my 5k ... octane ... location, ... Hmm. I think I'll try the exact version of the antilag code you posted and...
Howdy. I have a 91 turbo eprom ecu that I'm currently working on which has no 5v output internally. The 15 ohm buffer resistor checks out fine, but all 17 or...
Just out of curiousity, which way did you program for Fuel Cut Removal on the E931 bin? Did you change the 559A address to the maximum value of FF? Did you...
559A and 559B I changed to FF and 21 respectively. EA01 works with the extended map mod quite well. EA02 doesn't compare well with E931, addresses for injector...
i was just wondering if anyone may be able to help me figure out or tell me how to set up the equation format in the xdf properties. the only way ive been able...
... I was right: http://openecu.org/ These folks have already come up with the schematics for a decent little USB to OBD-II connector cable (and the site owner...
Now I know this is of topic but I have searched the internet high and low and cant seem to find what Im after, I rememered that some one on here said they knew...
Sorry I should have been more clear I was after the codes for an evo1-3. Shane ... From: Mark Rieb To: dsm-ecu@yahoogroups.com Sent: Thursday, June 09, 2005...
Last I checked, things were more or less at a standstill from the coding aspect of making the GM MAF mesh like a stock component with the DSM ECU. I propose...
I don't think you're stupid, but I think the part of the problem that you're trying to solve with hardware is the part that's easiest to solve in software....
Sorry to be uninformed on the subject, but I thought you guys had g/sec worked out for the MAF table? If not, shouldn't be too hard to figure out empirically. ...
My holdup has bee going through 4 GM MAS meters and all seemingly are broken. I can only get millivolt signals out of them. I might have to carve one up to...
How about a MAF translator? Maybe one that has Freq->Freq, Volt->Volt, Freq->Volt, etc? Maybe PIC-based? ... From: Dietrich To: dsm-ecu@yahoogroups.com Sent:...
If you are checking them on the bench the mass will need a pull up resistor to make it work ,as it has a open colector output .I use a 1 to 10k ohm when I...
sounds like a bad ecm with a resistor shorted to ground or something. if you got 4 bad MAFs then obviously something else is wrong. did you check the ground...
... evo1-3. The Lancer Evo 1&2 use ALDL for the fault codes & datalogging. The evo 3 uses OBD-II. Are the fault codes what you're after? Cheers, Alex....
Bingo! I would bet money thats his problem. Thanks for the good info! So, you just put a 10k resistor from the output to the +5 volt source? Jeff O....
... The sensor is 12v but the output is referenced to the 5v with a pull up resistor in the ecu .I have put a 10k resitor to the +12v when I check them on the...
I've added what I believe to be the OBD-II flash images for the cars we care about (1999 DSM and 3/S, plus 03 and 04 EVO) to the files section. I can see what...
... I don't know where Andrew stands on his conversion but I seem to have missed something in the process of doing a reverse conversion from a Turbo ECU to NT...
... Today I got access to a local NT car, put the ECU in and it fired right up. So perhaps I didn't miss anything but perhaps my customer did. :( Steve...
Mark came by tonight and brought his GM MAS and test kit. We found that my PLUG was bad. THen we used his connector and found both my MAS sensors I had were...
Would someone please check the their cranking injector pulse? I am getting 13 ms. It seems to be independent of injector compensation. I tried reducing my...
I’m installing my Innovate WB today and wanted to know what sensor input I need to use to log WB O2 with MMCD? I was thinking EGR-T but in the preferences...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
