... And/or a big fat FMIC. Hint hint ;) This big, black piece of VTEC linked to below belongs to a friend... 26X11X2.75" tube and fin FMIC. The air filter is...
... the whole map. The map was rescaled from kterry's posted map. Why do you have the CAS advanced all the way? When you do that, you increase advance all...
... You saw the ones I posted...right? Not that anyone needs to use those, but they're already out there. ... I'm probably going to switch over today or...
... You're not still runing stock maps, are you Carl? The stock maps suck soooo bad. I have seen a bunch of power (primarily at part throttle and transitions,...
... Made these changes and ran the chip on the way home. Worked the way it was supposed to. Even though my airflow/rev is artificially capped by the VPC, I...
... No, but I just figured if that was the only thing holding people back, at least there were already some stock-based maps out there if they were paranoid of...
... I logged 0x54 in the stock ... Carl, I've often thought about doing this, just remap one of the factory diagnostic values so I could watch something else....
... The useless TMO "airflow" value seemed to come from 8d or 8e, I wasn't sure which, so I changed both D02C and D02D in hopes that one of them would do the...
... I would if I had my timing belt cover on ;( ... OOPS soory, I didn't mention, I instrumented the air temp right before the throttle body. ... Funny you...
... Yuck! :o) ... before the throttle body. Ok. In that case, you need to compare temperature at the MAF to temperature after the turbo, because a lot of that...
... The calculators on my web page below can help separate the two. http://www.stealth316.com/2-turbotemp.htm I don't bother measuring air temp at my...
Stock or aftermarket. I was thinking about doing this on mine, but with a spun bearing it's low priority. Todd Honea I don't bother measuring air temp at my...
... If you are asking what air temp kit I used, it is the Autometer 3373 2-Channel Pyrometer. The ICs are similar, if not identical to, Cartech/Alamo's old...
Hi all, I've just started working on editing my chip to work best for my configuration. As I have 510cc injectors installed and my system has cyclone instake...
Yiuwa, Unless you have one of the JDM ECU's that the E952 is made for, or know how to rewire a USDM one to work correctly, I'd suggest you actually use the...
I've almost finished building my 4G63T'd 4wd 1995 Mirage/Colt, I'm using the GVR4 loom/ecu, once I've finished bracing the clutch pedal, I'll throw my...
... Anyone know a way to do timing without the timing mark? I think my cam timing is screwed up. The intake cam must be retarded by a tooth. When I did the...
Is this program still available? When I try to access the site that was listed before, it says I need a password to access it. Is it possible for someone to...
I am just about done fitting the GM MAS on my talon to calibrate it for the ECU. Amazingly, it fits right into the 1G MAF connector. The diameters are so...
I read that you could take a multimeter and blow through the sensor to test it. My guess is 12+ red, -12 ground, yellow for frequency. Give it a try and let...
I know we kicked this idea around at one time, but did anyone ever implement the idea of zero'ing out the knocksum whenever the clutch is pushed in? I'm going...
Now that I think about it i would say 5 volt. ... __________________________________ Do you Yahoo!? Check out the new Yahoo! Front Page. www.yahoo.com...
I kind of talked a guy out of it who wanted it, so I never did do the work to do it. Instead, he's been pretty happy using my lag reduction code that just...
Without looking at the code (I'm assembly blind) you want to reset the knock when the clutch is let OUT, not pushed in (or both, I guess, but knock shouldn't...
He resets it continuously when the clutch is in. What you are asking for sounds like "on trasition from in to out" which is much more difficult. Reseting it...
I think we are saying the same thing, except maybe reset it one last time once the clutch is back out then resume normal knock mode. If it's constantly...
Jeff- My car is set up to do this, has been for months. If you want my code I can post it up, but I think you're already in buisness. :o) I personally don't...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
