A used Haynes Dodge Ram 50/D-50 Pick-Up & Raider 1979 thru 1993 Repair Manual for sale on EBAY. This manual includes Plymouth Arrow Models also. Item number:...
... I'm in Australia, pity you won't ship o/s. I am seriously after a workshop manual for my L200. If it doesn't sell, and you change your mind on shipping...
I have an 87 D-50 2 wheel drive 2.0 engine. I was wondering if the trans. and rear end, of an 87 D-50 2 wheel drive 2.6 would work in my truck. Mike ps 5...
well i took out the shifter and the plastic bushing you (jamie) mentioned was broken,(the upper piece) and the lower piece was kind of side ways.well here's...
Dump the Transmission Oil and see if your missing piece is there, also look for water and metal. Oil will generally tell you the problem. Seive the oil and...
It should. If both engines are Astrons (Chain Driven OH Cam). I'm not to sure if one is a Saturn (Belt Driven OH Cam) There beleive there will be differences...
The engine bellhousings are different. The manual 2.0L is a narrow block (12.25" across the lower bellhousing bolts), and the manual 2.6L is a wide block...
But after 85, It should be employing an Astron II engine, which are all norrow blocks. The truck in question is an 87, I'm sure that would be using the Astron...
Here is my info for America. http://www.powerpro2000.com/lb_mitsubishi.htm Not sure where the guy is located but according to that, all the narrow blocks used...
Here is an extract from that site: Cap:2555 Cyl:4 Year:81 - 5/84 Description:Mighty Max Pickup, Montero, G54B, RWD, MCA Jet Head, 13 1/4" Across Lower...
I'm pretty sure you have misinterpretted the data given, so I will provide another source. http://rebuilt.net/Mitsubishi_Engines.htm Look at part 217B. The...
I think the whole point has been missed here totally! What I stated was there is two different size blocks! Instead of spending half an hour searching the net...
$50 sounds good. So you are getting a 2.6L Ram 50, what is broken on it, is it the engine that is stuffed? The rear end will fit the swap too. If the diff is...
'SOME' auto 2.6L trannies will work behind a 2.0L engine, and the rear end is probably identical, maybe different gearing, but the same size diff and axles. ...
The point that needs to be measured is at the widest point of the trans. Wher the two bottom bolts go, it will be either 12 1/4 or 13 1/4. Are you trying to...
Quoting cbsstv <jc218@...>: the owner told me that the head gasket was blown, still runs but steams. my truck is in good shape expect for a plinging ...
I would pull the head off the 2.6L and see if it is only a blown head gasket, or also a porous head. They commonly go porous around Cylinders 3 & 4 near the...
Jag... Nice lookingconversion rig, btw. more at the bottom. (On boardly-ish topic) Does anyone here have the addiction to check gas milage every tankfull? My...
Hi All: Just thought I would do one last post to this group before I go out and sell my truck on the local market. I have an 89 Dodge Ram 50 Sport, manual...
Hi all, I have been spending the last few weeks repairing rust holes in the Cabin of my '81 Mitsubishi L200. I have found two areas that are prone to rust out,...
Well everyone, Sorry that I have not been very active for awile. I have moved and started a very busy job. I have recently purchased a 73 Challenger. SO, I...
Other than the pistons and block that I have just listed on here. I also have an extra front axle out of an 83 4x4 D-50. I am running an 87 Raider and I can...
Folks, The coil and wires are gone, but the dual V. springs are still available. Lemme know...... Fred From: Fred Rupert <canook2u@...> Date: Wed, 9 Mar...
I currently have a 1988 ram 50 2.6l 4x4 5 spd. Found a 1987 Raider 4x4 2.6l automatic recently (cheap) and it came to mind to make a swap to be able to take...
Hey there, I just bought a 1981 Plymouth Arrow Custom last night and the funny thing was that I wasn't even looking for one! I went to this place that sells ...
If I'm not mistaken, the custom was pretty close to an entry level truck. Auto trannies are available and 2.6L's will fit nicely as well. Most of the...
Mike, You can drop your engine & tranny right in. Some models, you can just swap bodies on the frames. Wish I still had the compressor and bracket, but they...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
