Jeff, You say it's a 4by, my experiences have led me to use 2 floorjacks. One under the drain-pan, use a block of wood so as not to bend it, the other goes ...
... Thanks Fred, I got her down now. Turns out my clutch is broke. It's a shame too because it was a fairly new clutch. Plenty of surface left but it's junk...
Jeff, Please see my earlier post. Those wound compression springs in these clutches can get over compressed and somehow hangup on the rebound and thus get...
Cable-actuated Clutch adjustmenet info from Centerforce (Specific to Mitsu 2.6L, 2.0L, 2.4L): http://www.centerforce.com/technical_inserts/I93MB005.pdf I have...
... Are the retainer tabs the posts that the inner plate engages? If so they are flat on the side where contact is made and worn about halfway through. I hope...
I've got an '87 Ram 50 2.6 automatic and I'm curious about eliminating the balance shaft and doing some other simple mods to improve gas mileage. How...
A page every D50 owner should read: http://www.racetep.com/tips.html Basically, many of these tips and accessories apply to the naturally-aspirated 2.6, aside...
... I never understood this.... People make cheap aftermarket kits to remove the balance shafts, and charge more than you can get the mitsubishi parts for. I...
Do I just contact my local Mitsu dealer for these parts or do you have a somewhere I can order the OEM parts from? What sort of performance / mileage gains can...
... You can order them through your local Mitsubishi dealer, although, it will probably be a little more (we quote @ 25% off of MSRP). If you want to order...
get ahold of www.slowboyracing.com Fred Rupert <canook2u@...> wrote: Tony, The b/s's can be removed w/ out removing the head. You will need to pull the...
can you like just take the flywheel to a machine shop and tell them to mill so much, to lighten it? if so, how much do you mill it? [Non-text portions of this...
I haven't worked for Dodge as a tech since'96 and at that time they did not offer the kit. I asked local dodge dealer and he said napa. But if his shoes did...
Robert, Some shops can do the job, some cannot. First call around and find one who can, might run as much as $70.- or so. Typically, they'll have to see it ...
I got a kit from Top End Perf, very inexpensive. Try a search on internet for Mitsu 2.6 b/s elim. ... __________________________________ Do you Yahoo!? Yahoo!...
Hi All, Before I put my tranny back in place I need to replace a switch that has broken. It is the switch that operates the reverse lights when you put the...
Hey, I had the extact problem when I took down my tranny. Both the reverse and 4WD light swiches were cut to shot to solder back on. Although a friend of mine...
NOW THAT I FINNALY HAVE A LITTLE TIME I HAVE PULLED MY 88 RAM 50 OUT OF THE GARAGE AND TORE INTO IT, MY UNCLE HAD DRIVEN IT FOR AHWILE AND HE DECIDED IT WOULD...
Hope this helps,but Advance Auto parts has the parts much cheaper.The chain was 13.49 I paid less than 15.00 for the tensioners at my mitz dealer and you can...
I am taking the engine out of a 2wd 84 d50 and putting it into a 4wd 84 d50 that just needed an engine. I would like to know if anyone knows where to get my...
I bought a new head for my truck. I torqued it down and now the chain and gear doesn't have enough slack to fit up onto the camshaft. I don't know if this...
... had the same problem. I liked about a .25". I laid a piece of metal across the front of head in front of camshaft. Then got a small pry bar. Be careful...
Personally, I prefer WildCat EXTs on my rig - In fact that's the only tire I've ever put on any of my 4x4s. They have aggressiveness without being overkill,...
Hi, Just got my 88 ram 50 4x4 on the road yesterday after being parked since i bought it. Put another head on. I noticed head had been off before. I marked all...
Do you mean where the cable goes over the valve cover or at the lever on the carb? I got lucky - when I pulled my weber off of another 2.6 engine, someone else...
The easiest thing I've found to explain the vacuum lines is the sticker on the underside of the hood. Without that, you'll have to find someone who happens to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
