I have spent all night reading every related post and most of the last few days actually working on my 86 Ram50 --- But I still can't get it to start. Bought...
Hey I am having what sounds like very similar problems. I am going to start checking the exhaust today. Did you say that you physically cut out part of the...
Hey everyone, looks like I am talking to myself today. I don't blame you. It is Sunday, you shouldn't be wasting your time looking at problems on the...
Hi all, I just picked up my new engine the other day and I'm getting ready to drop it in hopefully this week. Since I have no garage and won't have any use for...
I have a question for you guys out there. for those that have been following along with those of us who have projects for your trucks, you may have noticed...
Good job, keep tweaking, you'll get it back to proper running..... Fred ... __________________________________________________ Do you Yahoo!? Yahoo! Tax Center...
It is already running better. i think the poor little thing just needed some time to clear it's thoughts. I still have a little pre- ignition noise. Turned...
I''m guessing a 2.6, right? I'm not familiar with the newer trucks - (only up to about 1986) - and I imagine the power steering pump and set-up to probably be...
... and I ... different in yours. ... need - I ... around from an ... Yeah you're right. It's a 2.6 The pump is an Atsugi MB 501630. Is that what you've got? ...
Hi Guys, I've finished dropping my new motor in, got all my vaccuum lines connected and am about ready to hook up the battery except for one problem. I can't...
I did a quick scan of the factory manual's ignition diagram and sent it via email. That should help. Bill Schiller 87 Ram 50 Long Bed [Non-text portions of...
I finally got to here my transplant motor run today. It fired right up and purred like a kitten after I got the ignition wired right and hooked up the battery....
That, I don't know. I'll have to go over to the shop and look to see what I've got out there. I would almost think that what you need would tend to be a...
They wouldn't have to eliminate the balance shafts to use a bigger cam, they probably would have to eliminate the MCA-Jets though, those little guys bend...
... I was just assuming if they were going to make improvements such as using an oversized cam, they would also go ahead and use a balanced crank and eliminate...
Hey guys, Some punk who can't drive bumped into my truck at a gas station the other day and busted the left tail light. Does anybody have an extra used one for...
I can't help you, but I read somewhere that turning an older Toyota tailight updide-down, will fit. If anyone can add to this, please be specific. Thanks, Fred...
Aaron, You are in luck. i have an extra left side tail light for the older style trucks. its in good condition, everything is there. The only thing that made...
Hey Man, I appreciate your return to my post. But right after I posted earlier my dad found one at a local junkyard. Thanks for answering my question though....
i have an 85 ram-50 any one know the color code wireing for the coil it has the resistor i just bought the truck and had the coil off and dont know where the...
I have a similar truck. 1992 Mighty Max with the 2.4 EFI 4 cyl. I recently had a similar problem with my truck. My mechanic initially thought it was the ...
I have a 1992 Mitsubishi Mighty Max with a 2.4 EFI 4 cyl. I've had the truck for about 8 years and it now has 160,000+ miles on it. I've had to replace the ...
Hi. I am new to the group and have a 95 Mighty Max 2WD with the 2.6L/4. The front bushings sarted squeaking last summer and quit during the winter. Now it...
... coil ... and ... Hi Steve, I just had the same problem you have. A fellow lister sent me a wiring diagram and I tried to forward it to you but got an error...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
