... Hey ya Mick I would go check out the (sidecar industry counci)l site of Doug Bingham . The place to get started what ever it is you are gonna do .He is a...
1980ish MT-11, had issues with it running and upon investigation, found I had valve issues on the right side. Talked with Ken Ulrich and decided to send parts...
Mark, check the compression on the right side, that squeak may well be a head gasket leak....Ken In a message dated 5/2/2009 8:31:00 P.M. Central Daylight...
Hi, I looking to replace the 2 into 1 Dnepr exhaust system for a 2 into 2 system. I looked on the web and found replica Dunstall "universal" mufflers that were...
I tried the Dunstall style mufflers. The bike was quite a bit louder (tho' not uncomfortably loud), and I never got them to look right. They sorta drooped. So...
I have a couple of Harley mufflers. They have a crossover fitting built into them that ends up in the same place as the Dnepr crossover. They flow better and...
Hey all! My left cylinder does not seem to operate. When the bike is operating, the only way I can get the cylinder to respond at all is by opening the...
Hello All, My interest is in the MT16 kit. I am well qualified for the undertaking and would appreciate any feedback on what to look-out for. I've read through...
Dave, I might take your advice - I looked on the local classified and found a fellow selling slightly used Harley mufflers for $20 CND a piece. Doesn't Harley...
Check compression, valve clearance, ignition timing, and after ensuring those are right, go into the carbs. You may find a lotta crud (rust, etc., from the...
Thanks. Have done all of that (to the best of my knowledge that is!!!). Could it be the dual exhaust without the crossover? Sent from my Verizon Wireless...
... Not likely. Tho, when you do find the problem, it'll prbably be one of those 'oh, duh!' kinda things. Like loose spark plug wires or something. SK...
Thanks! Sent from my Verizon Wireless BlackBerry ... From: "Sword King" <sword_king@...> Date: Tue, 05 May 2009 02:21:16 To: <dneprheads@yahoogroups.com>...
The crossover connection is on the inlet end of the mufflers. On a Harley, there is a top muffler and a bottom muffler, parallel to each other, the crossovers...
Hi Dave & Pierre, I have a mate who runs a pair of Harley slip ons on his MT9 - no jetting change & it gets along well. He's used them for years. I'm on my...
Thanks Guys, I'll phone the chap tomorrow and see if he can reserve me two harley mufflers. I can't really go wrong at $20CND a piece. Even if I'm not 100%...
So.... To try and make a long, painful story as short as Dneprly possible... MT16 sits forever, kid screws up what isn't already rotten/wrong already. I buy...
You are correct, it is saying ''I Love You!'' From experience... If the leak is not too excessive (I define excessive in this case as more than a few drops...
You might be better off taking your crank and rear case diminsions to a bearing house and try getting one there. The russian seals aren't so much crap as...
hello all i am looking to trade some welding equipment for dnepr ... i have several wire feeders and some other metal working tools in duplicate and would be...
I get to take a day off tomorrow and I hope to finish dismantling my Dnepr MT11 engine. So far I got the cam out and would have taken out the lifters, but...
i just got finished fishing through the links here and found that most r obsolete or non existing at this time anyone have a current list for dneprs as kits...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
