I bought mine from Ramco. Lloyd is a little hard to get ahold of nowadays, but i think after he gets all his stuff moved things will get back to normal. ...
Lloyd usta have a really cool custom made aftermarket set that was probably far superior to stock Dnepr exhaust. I have two cucumber mufflers in stock, but...
I have Lloyd's duals on the restoration he did for me. Much easier to start, less noise, back pressure very minimal on the engine. So far a very nice...
Dual Exhaust. I bought two MT-11's Kitbikes (via canada) in March '01. I bought 2 thorpedo Mufflers and 2 crossover pipes. I fitted one bike with the two...
I need to get a title for Yuri dnepr-16,it is listed as a 2005 dnepr kit bike.I contacted ITS and would not give me advice.How should i summit it?As a 74 and...
When I talked to ITS, he said if it was newer than 79 it had to have a 17 digit serial number. If not, no way. At one time, Yuri would do the paperwork for...
You need to really look into what your particular state laws are concerning "homebuilt" or "kit" vehicles. You will probably have to show receipts for all...
I used International Title Service to title my Dnepr awhile back and it was quick and relativley painless. Because it had the short VIN number they registerd...
Interesting ....... I'm currently looking at a bike that is registered in Alabama. From the sounds of this thread, it may not be exactly what the title says...
I got my bike from yuri's brother in 06. I used ITS and just told them it was a 1980 and gave them the number on the frame. I don't care what year it is, but...
Very wise advice....took two letters of authenticity, then affidavit of origin of engine and transmission, police inspection (had a crowd of curious cops there...
I have a wonderfully restored MT-16 that Lloyd finished this past June. I am trying to locate a carb tuner for the pair of Edelbarg carbs placed in my new...
Yep...and so the fantasy goes....Ken the Alabama title can be correct as the local Judges can title. Sometimes it is worth it to take a cheap flight to...
If you haven't fiddled with the idle or throttle cables since you got it from Lloyd, the carburetors are all ready in tune. Lloyd's chief mechanic, Stepan, is...
Thanks for all the suggestions about exhaust. It is the next "performance trip" I need to take. Getting back to the ignition question. Does anyone know what...
this is an open message to someone I was corresponding with about some used dnepr parts. You did a vw conversion, and Live in Kenora. Due to a computer...
Thank you Dave....have not touched the carbs since it returned want to measure them now so I get a good baseline for future reference. Lloyd and his Stephan...
... Dub ... should be ... Am I ... at least half way you should see the flywheel advancing toward the p mark. ... bought 2 ... the ... Crossover ... to out ......
I have a k750 motor and it will not run on both cylinders when started. It did once, but only briefly. I am not the most expirenced wrench so I was wondering...
This is a pretty generic reply, but it's all I've got! You may as well go thru all your settings, even if some of them are good, you're going to need to get...
As long as you can get it to run on one side, you can probably get it to run on both. The carbs are probably out of sync. Typical. What you do is get it...
Hi, Just wondering how you ended up solving the oil pressure problem? Pierre ... great now, and it is still purring. Dean ... Very low oil pressure....Best...
Problem solved. I'm just waiting on the part... The cause: a snapped off hollow oil pressure feed bolt on the front of the crankshaft. The cure :a new custom...
One of my future projects for the MT-16 is to overhaul the transmission. Even though it has less than one thousand kilometers on it. second gear has an...
... All the bearings in the transmission are common available bearings from your local bearing supply house. Just remember to ask for C3 bearings (class of...
So I saw one of these bikes on ebay awhile ago, and have wanted one ever since. I was wondering though where you guys would recommend I get one from. It...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
