I would prefer to sell entire M/C. I would love to receive a email from someone who wants to buy the complete Dnepr. Actually, I would prefer to keep it, but...
ahh. i took my mt10-36 out sunday for a nice ride with the kids. next day i find gas pouring out onto the driveway through the right carb tickler. (silly me...
Hello Mr. Shane, I have never messed with Bing carbs, only the Russsain copies. If it were a russian K-37 or K302 I would say either a stuck float or the float...
www.theborgenterprises.com I have one left in stock. Won't get any more until next month, so get it while you can, the Borg John <cytop450@...> wrote:...
Wow Larry, It seems like a real shame to part out a bike like that. That fella that offered you 250 wasn't a real buyer, he was just trying to get something...
I'm trying to work with people on this. I cant ride 'solos'. I had a stroke, last year, and lost my right side balance, that's why I started shopping for...
I'm running Bing's on my MT10-36 also. I would try just tapping on it with a screwdriver. If that doesn't fix it, take them apart and clean them. These...
I opened them up after work, and of course the float was down at the bottom. but it wasn't stuck there. it was full of gas. there appear to be hairline cracks...
If you Solder really well and know about rosin and Acid fluxes, you may be able to repair them yourself. First you must get all the fuel out and repair the...
now that the carb problem is more or less solved, i have found that the kick start lever won't return to the top position on it's own. what next. my manual...
The spring tension can be adjusted if you seperate the engine and tranny. Once they are apart its fairly simple. For anyone interested, Nathan Mende (...
Thanks. For now i've got a bungee on it to hold it up out of the way. Good thing the bike is starting on the first kick (when the carbs work!) ... tranny. Once...
Hi Shane, You can solder the floats. If you try it, make sure you use as little solder as possible or the float will be to heavy and not shut off the fuel...
thanks, I'll give it a try! ... little solder as possible or the float will be to heavy and not shut off the fuel flow correctly. ... down at the ... appear ...
now another, possibly stupid question. in laymans terms, what is the procedure for separating the main drive from the gear box. my manual is about as clear as...
Hi Folks, Uncovered a few new things from the parts pit! I now have ignition wire for sale if anybody needs it. Check it out at www.redoctobermotorcycles.com ...
Yes I was! Solved my float full of fuel problems. I had tried soldering my floats but I wound up chasing cracks around the float. Also found the float was not...
Parts for all of your Bing needs can also be purchased directly from http://www.bingcarb uretor.com/ . Jack __________________________________________________ ...
After i rebuilt my mt-16, i installed an oil pressure guage that i bought from a harley shop. It goes up to about 100psi i think. My engine would run about...
I've been using a glycerin filled gauge for more than a year now from Northern Tool. It's part number is 53610 and a year ago it cost $11.99. It's face is a...
Contact Ken at U2cycles, he have the complete kit set with three guages. I got the set from him and it works geat. It comes with all the parts needed to...
Pull Axle out.....then wheel off the shoes and out....Then the final drive with the brake shoes attached or you will find they pop off really easy and might...
Mike....If its just the guage you need I have small 1 inch stainless liquid filled 0 to 100 PSI that works good either on the handlebar or at the T in the oil...
im trying to adjust my rear brake on mt11 i take the play out of the pedal with the square headed adjuster on rear hub and it has no bite hardly at all,my pads...
Keith, You may need to go to the other end of the rear brake mechcanism to begin your adjustments. I believe there are two places to adjust. The first is a...
