... Actually, I doubt that as, when installed it is invisible. They are likely annoyed at being on the side of the road with their crappy oem electrical system...
Does anyone know of the bearing and race #'s to convert forks to cone bearings or Is BMW the only place i can get them? I'm looking for a set of bearings and...
Got a problem with my dnepr reveing smoothly- I have a new harley coil , new chev condensor, k-68 carbs and the bike runs without overheats-yet will not rev up...
Got a problem with my dnepr reveing smoothly- I have a new harley coil , new chev condensor, k-68 carbs and the bike runs without overheats-yet will not rev up...
The very first thing I would check is to be absolutely sure that BOTH throttle cables are hooked up at the slides. A bike will act as described with one not...
Chris, I have K68's, a Harley coil, Harley condensor and stock points on my MT10-36. I've adapted Scooter Bob's K65 carb setup instructions to work on the...
Riding home last night my baby started spitting and sputtering real bad, it wouldnt even stay in fourth gear. It died once and I changed the spark plugs on the...
Hey Mike, Thanx for the link. I have a set of K68's for my bike and haven't been brave enough to do the swap yet. Fortunately the Bing /2's that are on it are...
Could be bad gas. Could also be (in no particular order): Bad coil. Clogged petcock screen or fuel filter. Pinched/kinked fuel line. Rotor loose on the...
BMW isn't the only place. They buy them from somewhere. I have a brand new complete SKF bearing catalog that I've been meaning to get into. If I find anything...
Sort of. If you look at the bearing sets from any of the BMW shops (they undoubtedly all come from the same unknown suppliers' garage or basement) you will...
he just replied, but thanks ! ... From: "arbalest04062" <no_reply@yahoogroups.com> To: <dneprheads@yahoogroups.com> Sent: Tuesday, August 02, 2005 6:43 AM ...
I had the same symptoms,and i tracked it to air intake, The paper element was saturated ... ____________________________________________________ Start your day...
Sat. 6am My son and I set off in My Dnepr powered Chang.We where headed for Sunday river just outside of Bethel Maine for an overnight at the Western Maine...
Now THIS is a story of simple technology maintained by a creative 'shade-tree mechanic'. Try that with your 2005 zillion-valve megacylinder Japanese sport bike...
Now hal, I'd like you to take care to answer this question......................... WHAT THE HELL DID YOU DO WITH THE STRING! KEN ULRICH U-2 Cycles Here I...
Ken, I wasn't there...just commenting. I have, however had to resort to similar techniques in the past. Unfortunately, when the situation is desperate enough...
In a message dated 8/3/2005 7:25:10 P.M. Romance Daylight Time, dneprheads@yahoogroups.com writes: Now has anyone tried to install a rod with the other...
In a message dated 8/3/2005 7:25:10 P.M. Romance Daylight Time, dneprheads@yahoogroups.com writes: Simple, cut the string off before the nuts are tight. I now...
... that takes ... locktight in ... It happened to the Dnepr engine that is in my CJ. The original bolts have castle nuts with cotter pins.I have never heard...
Do any of yous guys have a set of the rhe old style header pipes,and old style muflers ?The header pipes are about 3feet long. The condition does not matter,...
http://pokazuha.ru/view/topic.cfm? key_or=607266&rate_old=10&type=98&lenta_type=2 I found this on the Pokazuha.ru website, While most of the photo's are babes,...
I got my Motor back from Ken. It looks great and I can't wait to start her up. Pics and comments on my restoration page: http://edslastresort.com/dnepr ...
