Ok. Im just gonna list what happened and if anyone can give me another pointer as to what is wrong Im all open. I am meant to be driving to Dublin on...
That is why we have Mr.. Fusion!!! Make that first. Richard ... From: dmcnews@yahoogroups.com [mailto:dmcnews@yahoogroups.com]On Behalf Of Ryan Wright Sent:...
The new stereo is probably the culprit. I had mine put in by a professional shop and had about the same thing happen. In doing it they had loosened the wires...
You may remember my question about getting an oscillation (back and forth) upon braking from high speed (freeway offramp). This is an update to that post. ...
Paul, Does sound like bad gas or to much moisture in the gas. Yet, if you parked it out side and it rained then you most likely have condensation inside the ...
You may remember my question about my A/C-Heater fan cutting out when put on the "4"/high speed position. The fan would run consistently on all other...
I did NOT know you have welded torsion bars on your website. Can you tell us how many you have done? How do they hold up? I guess you won't share with us how...
Hey Group, I am not very good at troubleshooting electrical problems so I thought I would see if anyone else has had this problem. My reverse lamps stopped...
For those on the list interested in BTTF, your very last opportunity to ride inside the DeLorean time machines at 'Back to the Future...The Ride' in Los...
The only things that jump into my mind is bad gas, RPM relay has gone bad, or the connection into the inertia switch is corroded or melted. I saw a post...
... I am interested in making one, too. Can someone post a list, including manufacturer's item numbers, for the basic parts needed? For example, which specific...
Andy, It sounds like you checked voltage on the wires where they attach to the switch. There is a wire junction (a simple plug) just behind the engine. The ...
Andy, You are absolutely right, the torsion bar has a really low failure rate. BUT, and that's a really big BUT, until it happens to you, personally, you...
It used to be my car. I sold it a few years ago and just saw it on there tonight and thought I would check the list to see if it were mentioned. Aaron Posey...
Instead of checking the switch for voltage, you need to check it for "continuity". Take those two female wires off the switch again, set the meter to check...
If your brake fluid was that bad you can expect the master cylinder and the calipers to start leaking. Keep an eye on the level in the master cylinder. If it...
Sure I'll share it with you. I didn't weld it. My customer had someone up in Oklahoma do it a few days after it broke and he didn't want to pay the $1500.00. I...
Hey guys, Has anyone else had a problem where their seatbelt buzzer (I think that's what is doing this) seems to get a very weak connection somehow and it...
Never said to use THE Bricklin doors or even the Bricklin setup..Please get your facts straight..just THE type of system Bricklins use...which is a *AIR DOOR*...
Andy, the switch is just that - a switch. You need to test continuity with the tranny in reverse. See if your meter bleeps when you touch both pins. There is...
... Thanks for your suggestions but it turned out to be the ECU that's faulty. I begun to testing it and it does not respond to the timing signal from the...
Hey Lars, if it won't respond to the ignition signal - why would it reduce speed after 5-7 seconds ? Fixing the ECU takes less than an hour. (if it is broken) ...
Try this simple test - get under the car and remove the connectors from the reverse switch. Have someone turn the key on (ignition, but without starting the...
When you say the ignition switch I am assuming you are referring to the the actual key barrel behind the steering wheel. I know its sounds very stupid and...
Claude, I knew what you meant the first time and I still feel the same way.? There's plenty of DeLoreans for sale, and I would throw mine in the trash can and...
You may remember my post re: this topic. It was suggested to me (by Rob Grady) that all studs should be replaced, but I am not in a position to do so at this...
Hi Wayne, I have put a few 'dusty work in progress' shots in the album named Australian DeLorean. I didnt have alot of good engine bay ones on file. I will...
Patience does pay off. When you are faced with a broken stud you have to figure that the gasket is damaged from the loss of clamping force. You should remove...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
