Yes , my ears have been buzzing since 1970 or so , the doctor says it's Tinnitus but I'm not so sure...... :-) . I change the subject title to reflect what I...
... Seems like it'd be simple enough to fabricate one -- I personally would use steel bar stock, and then powder-coat the thing when done. The big trick would...
Ray , you have a significant problem , I'm betting it's the regulator , easy to check by disconnecting only it and checking for the draw again . Any draw big...
Oh - I see (snicker) want to sell me some P.D. license plates ? . what state are you in ? . I could tell some Cop stories but would likely loose my job.... ...
Steve ; WELCOME to the group ! . You appear to be my kinda guy ! . -Nate ... motors and beer.thanks for the heads up nate, there is no other way to do it...
Firstly , NO question is dumb ! . Now , it appears you need either a new carby or a parts carby to rob for the petcock parts you need . If you go back in the...
It should return _fully_ to idle with no problem , if not either your twistgrip assy. is internally filthy (common) and you should clean and re-grease it , or...
I knew you'd figure this out ! instead of elecrical F.I. , maybe a fully mechanical typ ? with poppet valves like Bosch C.I.S. ? I don't know how you'd do the...
Either your local Honda dealer or a V.W. shop should have the bulb you need , make sure he knows youwant a 6 volt bulb !. -Nate ... extension ... a ... )...
I regularly use Aluminium alloy bar stock that is pretty hard stuff and yet easier to precision bend than steel and, of course, without the weight. And welding...
Well , at least you're trying ! keep at it and you'll get it knocked soon . Firstly , the impact WILL NOT WORK unless you bang the HELL out of it using a 32Oz....
... investigate? ok, this may seem like a dumb question, but are you sure you removed the oil drain plug? there is another bolt down there that looks like an...
... I thought about the pump about 30 seconds after I posted the last item about this, but if you went all-mechanical you'd run into the problem of having to...
Good deal ! remember , when you teach her how to ride it , go slow ~ just show her the basics of starting and stopping then let her ride at _her_ speed around...
... investigate? ... driver ... it "pretty ... Are you sure that you are removing the oil drain bolt and not some other bolt from the bottom of the engine? If...
haha, I've got it, a diesel ct90. you'd get 800 mpg, and you could still go 50mph, it would just take you 6 years to get there. Seth S ... don't ... like ... ...
... Yep -- the single best rule is, remember to have her start off with her wrist below the handlebar, not arched above it, so that the initial torque from...
I think the way to do this would be to either modify the flywheel side over so that you could extend a shaft off the crank to drive a pulley for either a...
... Seems like if you were willing to live with this big lump sticking out of the head, you could machine a fitting off the end of the camshaft, and put a...
In a message dated 6/28/02 9:41:29 PM Pacific Daylight Time, ... What I meant is that you can have the prior owner release interest in the title, but you do...
These pages are in Japanese... but the images speak for themselves. You may want to try babelfish or something, or with any burning questions I can attempt to...
Well, from my days as a target and surveillance drone engine engineer with Piper FM and Norton motorcycles (well, my Automotive Engineering and Design degree...
In a message dated 7/1/02 7:36:02 AM Pacific Daylight Time, ... Why, you drive it with the cam chain, of course. You modify the left engine cover and lengthen...
Well I heated up the foot lever and bent it back. It lasted 2 days before breaking off completely. Which really isn't a big deal because of the two brake...
thats exactly what a CIS system does (Constant Injection System). One thing that you would need to do would be to put in a throttle body, or some sort of...
if I start playing around with this, I'll just get a second parts engine, and work off a bench. I probably will use an outside power source to run the...
Hello Dave. I have not seen any replies to your question. I would think that maybe you have accidentially done the same thing that I have done once in the...
