Well I suited up for my first ride today and headed off on what seemed to be a well running bike. I went down the dirt road a ways, then went into low range...
Well I took the left cover off the bike and inspected the timing marks, the chain, the tensioner, and remeasured the valve clearance. Everything was dead on....
... I ... go ... Mine did the same thing to me once on Mt shasta. But I was climbing a steep hill and had been for a couple of miles. It had to have been ...
Well I wasnt able to start it after it died the last time, and when I tried to kick start it, it didnt sound too good. I now have both the left and right side...
Hi Everybody I am new to this group but it sems like an very valuable source of info!!! I just picked up an 83 and 84 ct110 and one of them needs the back hub...
Read about curing rattle can paint job in the oven in this group. Tried it, set oven to 150 and baked them for 3 hours until the spousal unit came home and...
... Clean that oven before using it to cook food. Unless you like ingesting paint residue. And for future reference, NEVER cure paint in a food oven! Get a...
I have a CT90K4, It almost always starts first kick. I will ride for about 5 mins.(The bike has warmed up by now) Stop at a set of red lights. Change gear...
I throttle up and it ... Check your battery, 6+ volts is what you need. If less, charge your battery then check your charging system. (rectifier failures are...
The hole on the right side of the frame at the base of the downtube? Plug wire? Main Harness? Fuel Lines? Which items then go through the raised relief in the...
... Let me see.... You might like to pull the generator off and then remove the backplate from behind it to check the timing gears and chain behind that. ...
Hi all, Pre-tune up, I was able to get 45-47 mph top speed slightly downhill and 42mph cruising speed on the flat. Post tune up (new plug, adjust valves,...
On my 66 the fuel lines go thru the Rt side hole. I don't see a raised relief on the left, is it under the cover on that side? My key switch is there. -Outlaw...
Thanks Outlaw. Am I correct in assuming that the plug wire and the main harness both pass through between the top of the engine/trans case and the underside of...
My harness pass thru a bit to the left, and the frame has a clearance notch so it won't get pinched. I doubt it matters which is right or left in the notch,...
Well i finialy got the bike back to gather and running have been taking short rides around the house fixed a elec. problem with the horn. I need to get the...
Guess mine is running about normal, then. Just not enough speed to feel comfortable on the road. Feel like I am going to get run over from behind. Be...
The thin plastic covering on my K5 front brake switch wires to the hand lever are brittle and broken in many sections. What do I use to cover them? I was...
In the end Jeff , I agree - as long as it's fixed the reat is all a wash.... I also realized _after_ I'd hit the ' send ' button that as an ex- Yankee living...
Sorry to hear of it Seth , remember usually it's the simple stuff that causes the biggest headaches... keep at it buddy ! . -Nate ... and ... isnt ... can ... ...
Yes , I think you can . one of my favorite 90's is _beyond_ worn out but still runs so I ride it like that , if I leave it in gear at a red light , the plug...
The two fuel lines _always_ go through the round hole on the right , the wiring harness goes between the frame and engine , not all models have the relief but...
Yes , I was riding my son's CT90 downtown to Jury duty a couple years ago , it went 50 + on the freeway and easily kept up with morning rush hour traffic . ...
Cold day in Hell before I'd get on a CA freeway riding a CT90. Damned if I know what the average freeway speed is here in south Orange County but I'll bet it's...
