I had the same thing happen! I tried the JB Weld idea---it worked for about a week and then came loose. There just isn't enough room in the case to make it...
Randy I recently rebuilt the worst looking carb I'd ever seen on any bike. All the components were completly stuck I soaked it in gunk carb cleaner for two...
Try turning the handlebars in the other direction. I had that trouble once and had the throttle cable routed wrong. I could turn to the right and the engine...
Jeremy In setting up a new carb the throttle cable needs the slack adjusted out of it where there's a little less than 1/4in of play when first twisted open ...
Kevin Have you had any luck on your stuck carb parts?? Has your patience payed off yet. One recourse is to pickup another carb to use in case parts get broke ...
Ok here is the latest. I have actually gotten the emulsion tube cleaned up enough that I can see the tiny holes down the sides. What is the best way to...
Randy.....If you have them, the best to use to clean the holes is Oxy-Accetelyne gas torch tip cleaners. If not, get a small multi stranded wire and take one...
Randy.....I doubt that the Honda shop will have anyone with the knowledge to even rebuild your carb! If they did, you won't get out for less than $200.00 for...
Jeremy, make sure your throttle slide is not installed 180 degrees off. I didn't think it could be done but I did it. The cap even screws on but it will be...
Thanks Kenny, I am thinking the same thing. I am trying to get a good carb as I start in on this one. I was wondering if I am missing something a catch or...
The same thing happened to my 1978 ct90, but it happened before I bought the bike. I only learned about this when I first changed the oil and cleaned the oil...
Randy A good shot of compressed air blast will clean it. If you use wire (Steel Wire) you might widen-up holes that need to be that size and leave bits of...
Hey all, I've been working on my CL-100 on and off for about 6 months now, and I still can't seem to figure out whats wrong with the engine. Recap: I put a...
Can someone please describe to me how the Honda CT90 AUX fuel tank would mount on a 1968 model? Is a special bracket required or does it bolt to the fender?...
After successfully removing and cleaning the emulsion tube in my K6 I had no success getting the float pin out even after soaking and heating and beating with...
George, there is a bracket about 2 1/2" wide. It looks like someone cut a strip out of the fender.Actually it sticks out a little on the left side so the nuts...
That float pin has got to be able to move with the float.The carb is a living, breathing, drinking thing. Don't waste your time expecting it to work. Soak it...
Yje float valve seems to be OK. The hing pin for the float is what I cannot get out ... is a living, breathing, drinking thing. ... K6 I ... is ... this ... ...
without replacing the fload valve" I understand now. I had been following your problems with the pin that goes through the two posts. I had that problem and...
George, It does mount with this bracket. I finally won one on eBay. Now I have all the pieces to mount it. If you look on DRATV, you can fine a picture of...
There is one on ebay in the bigfootedalien store listed under 8/73 HONDA CT90 GAS CAN BRACKET ASSEMBLY for $37 and actual shipping costs. Looks okay. Phil...
Phil, This is the bracket that goes over the gas tank and mounts to the bracket that George is asking about. The Gas tank takes two brackets. The one on eBay...
I bought a new float (it think it was $9.99) for my cl100, it had a new pin with it. i had to file down the end of the old pin to remove it. Somebody (maybe...
This may be old news, but Yahoo is reformating the photos section and the changes brought the locked up photo section back to life! it also resized the photos...
I already have the tank bracket. What I need to know is how does it mount to the bike. Is their another bracket I will need for it to bolt to the bike? Thanks...
All-right Wayne, You're right, the 'photos' folder is now up and running. Thanks for the update! Miguel '74 ct90 ... it ... Group ... though ... album ... a ...
