Don... Sorry but I can't quite make out the number of the part on the fiche in order to get the part number for the hose..But..I think it is NLA.. But I was...
I recently won an auxilary gas tank with the bracket, rubber pieces, and helmet holder/lock. The winning bid for me was $81 and I got the tank the other day...
Hi Tobias, thanks for the reply. I'll make sure that the battery is new. Now that you mention it, I think I remember seeing the reference to the battery acting...
Does anyone know where early seat covers like these are available outside of once a month on Ebay? I guess I could just email the guy but I get the feeling the...
... Check the Parts links on the CT90 site... there's a place that does motorcycle seat restoration. It won't be cheap (at least $80 to $100) but their work...
i jyst bought a ct-110 about a week ago. when i bought it the guy didnt know what year it was. i need to know the year so i know which owner manual to get....
Hi All, Now that I have run my 71 ct90 a little, I see I've got an oil leak. It appears to be coming out of the surface between the head and the cilinder on...
The VIN would help a lot, and realistically, the owner's manual for every CT-110 except 1980 is pretty much identical. Matter of fact, the owner's manual for...
... anyway i can easily identify ... have ... bordered ... Yo Mr. Dr.; Just went out and looked to make sure, and on my 82 110 their is a plate on the stearing...
... anyway i can easily identify ... have ... bordered ... Yo Mr. Dr.; Just went out and looked to make sure, and on my 82 110 their is a plate on the stearing...
... The bike is stll at the Honda guys place. I paid close attention to the note that Turtle posted about getting answers from my Honda repair shop first, so,...
Allen, I am not the brightest spark but I suggest you confirm first that you indeed have a good ground. Check the voltage with the headlight hot wire and...
... you ... an ... voltage ... Hi Jim, Thanks, that sounds like something that has not been done (and it makes sense to me). I'll look into it. Thanks. Allen...
Good morning Spencer , there is indeed a rubber gasket in there just for the cylinder to head timing chain cavity seal - my recommendation is to buy the...
I am looking at a 1969 or 1970 CT90 for sale and wondering what the value is. It is in fairly nice used condition with 1100 miles on it. Comes with buddy...
I looked pretty hard for about 2 months before I found my 1971 honda ct90. I paid $550 for it and the guy I got it from was more then willing to help me out...
... DC voltage doesn't work the same way, not in the sense of combining two 110v hots AND a neutral to get 220V to run, say, a dryer or arc welder. DC adds...
I would not be too impressed with alleged mileage on these bikes. I bought two 1977 models with the odos showing less than 2500 on both of them but they were...
Is there a way to make the horn button a kill switch? (without cutting any wires) The horn got smashed so I have a good button that needs a purpose. Its my...
Well, I traded my big bike for a CT90 that I think is a 1969 but not positive. Is there a place on the net to look up the vehicle identification number?...
After looking at TURTLES Website, I figured out that it is most likely a 1969 K1b except that it has the air intake up higher like the 1970. An in between...
As far as I know, unless someone retrofitted a 1969 with the later rear deck and intake (the 1969 rear deck, to my knowledge, lacks the fitting onto which the...
If you really wanna do that, find the lead that grounds the horn, and T that into the ignition primary lead (black, cloth-covered wire that slips down through...
It has steel foot pegs, horizontal slots in exhaust guard, I think small headlight (don't have one to compare with), no fork reflectors, and even says 1969 on...
Based on all that, I'd say definitely, "1969." I'll be the VIN is "CT90-2xxxxx" because 1970 started with "CT90-3xxxxx" Probably a long time ago somebody...
