They are suppose to have a 223 mile '75 up for auction this year, lot number 637. Wonder if it will make the TV show. By the way Britt, I sold Tom a number of...
Where is the fuel check valve in the fuel supply line? The HP fuel pump? The in tank pump? The FPR? When the car was first started after being parked for...
It's in the outlet nipple of the high pressure pump - easy to test - it should hold pressure and not flow "backwards". You should be able to see the steel...
Have any of the past issues of Cosworth Times or other Cosworth Vega specific literature that document how to repair a coolant temp sensor. Even a wiring...
Hey all I need to know where i can buy rear sway bar bushing . I bought everything else at performace suspenion teck but they dont have them. I also need a...
Steven The article I cited you to, "A Journey to Discovery", contains the circuit diagram. And a full explanation of how it, and the ATS, work. Nobody to my...
There are no sway bar bushings unless you are talking about the panhard bar or lower control arm bushings. The sway bar "hard mounts" to the lower control...
Hmmmmmm Smething to ponder I guess. Is there such a thing as NOS on a CTS? You mentioned you might have a good used one, when you know for sure one way or...
Hey Bob I am talking about the bar that goes from the top of rear end to the body . Not the bar that goes from the nose of rear end to back of trans or the one...
Hey Bob I am talking about the bar that goes from the top of rear end to the body . Not the bar that goes from the nose of rear end to back of trans or the one...
Gary You are not quite correct - the VW, Porsche and Volvo used a Bosch EFI system were as our's (and the Cadillac) were a Bosch - Bendix combination with the...
Dave, That's the Panhard bar, locates the rear axle "side to side". bob David Garrard <vegaman537091@...> wrote: Hey Bob I am talking about the bar that...
Hi All, I am sure this is an old question, but does anyone have a Kent Moore (J23654) or equivalent tool for adjusting the CV/Vega timing belt tension...
I guess I'll have to get back on my drafting board with a pencil & design one that you can make with a hex head bolt and about a 1/2 x 3/4 x 1 3/4 inch piece...
bob: Instructions and photos showing how to make this tool are on the CVOA website, www.cosworthvega.com, under Tech Corner/How To. A set of engineering...
Brent: There are two links at the bottom right of the Home page: Renew your CVOA Membership online Join the CVOA online I just clicked on each of them and they...
Thanks, Tim. I was under the impression that the CV sensors were the same as the others that used the D-Jetronic. Even if the CV parts were made by Bendix,...
Gary Duke can probably give a better explantion about the connectors but I think it's to match Bosch connectors used on the EFI Harness for the Bosch...
Hi there, I got the cylinder head back for my car and it only took 5 thousanths to make it true. I had it checked and new valve stem seals installed on the...
I've got a panhard bar with hard "plastic" suspension bushings. Took a stock bar to a local speed shop years ago and had the rubber bushings cut out and new...
Hi all - quick question. I'm replacing the alternator on #1103. I haven't been able to get the top long bolt out. Is there a trick to getting it unstuck from...
Chris: Here is what I have done. Try penetrating oil. Unlikely to work So, remove the alternator and bracket together. You will have to remove the K-member...
Mark, I tried that and I couldn't get a download to start, yet it asked me to confirm a successful download then flashed me (red!) for not having restarted my...
Brent: Is it a firewall issue? Is it some other security program on your computer that is preventing the installation? Have you tried the "Manual Download"...
A week and a half ago Stainless Works introduced a collector which may be of use to Cosworth owners making custom exhausts. It should be just the ticket for...
Mark, I checked in my add/remove programs to see if I actually had a Java download, and I have 1.5.0_06 - not the latest but at least it's there. I'm running...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
