Hey Tony Your computer is working fine now .How have you all been doing as for me iam doing fine my dad is still in hospital he went into a relapse.they had...
After passing my emission test I've done some more tuning in non-emission configuration to optmize driveabililty. To eliminate some idle speed inconsistency I...
a while back the yenko vega was discussed, there is a photo on the Hot rod site at http://www.hotrod.com/featuredvehicles/97138/ I like the front air dam,...
What is the prefered method of refinishing springs and sway bars? Powder coat, Enamel, Laquer, other? I am almost finished cleaning the rear springs and will...
Everyone: If you thought Tips and Tricks I was worthwhile, wait till you see Cosworth Vega Tips and Tricks Knowledge Base II. Now shipping. This volume picks...
Refinishing springs and stuff? Clearly the preferred method is chrome plating! At least for me, anyway, I love chrome (just can't afford it!) Actually, on 2584...
Hello, As I am still in my search for the perfect Cosworth for me, I did run accross a fellow that has some he wants to get rid of I thought I would post on...
Last week we had trouble with Yahoo chat and we were trying out the chat in http://www.cosworthvega.com Mark would like to try it again they have different...
Chatters: Here are instructions on reaching and signing in to the Chat at www.cosworthvega.com We are trying it out as we are again beginning to experience...
I guess there is no one who knows if there is any mfg that makes lowering springs for the CV......................... No responce to my previouse posting. ...
... I have always used a circular saw to cut my springs. A quarter of a coil here, a half a coil there, and voila, lowered. However, my approach is not the...
Just one last note, practice makes perfect as they say, it took me two sets of springs to get the desired height i was looking for for CV 1002. Later, John J....
There were people way back when. Go to the search engine on Cosworth vega web site and check out the discussions. Duke has a number of thoughts on the concept....
Gerald (or Duke), Did you run the cams "straight up" or did you reindex either of the cams? If you did reindex the cams what did they get reindexed to? I'm ...
The process I went through to determine the ideal indexing of the production cams is extensively documented in the Twin Cam Times Portfolio, which is available...
I ran the cams straight up, no re-indexing. That engine made about 200 H.P. (an estimate since the stock cams with high compression and webers would make...
For Sale, 4 Kumho's Victoracer, P205/ 60/ R13 Heat cycled $500.00 plus trade in CV rims, trade in rims preferred 75' but will take 76', must be in decent shape...
Wondering if anyone has any experience with Jet-Hot ceramic header coating? Is so, how has it held up in terms of durability, looks, and did it really help...
After sandblasting mine I sprayed a light coat of primer followed by "natural cast" grey paint. It has held up perfectly for several years so far. This paint...
Probably the best overall coating system for coil springs would be POR-15. It is flexible, and is pretty darn good at inhibiting rust. Don't get it on your...
As far as the coating holding up, it has very well. I had tried a couple of other coating places before trying Jet Hot and they discolored and faded and...
... both ... heat ... of ... know ... posts ... headers ceramic coated from Hooker or I can purchase them directly through Jet Hot for a little bit more. I...
Hey All, This is a question I don't think has come up before here. While in the process of replacing the interior carpet in 3087, I found that the rubber...
Good Morning all! For the past few rides i've noticed my Volt gauge bouncing back and forth a bit between charge and discharge. It never goes into the red and...
... and forth ... is not ... not the ... comfortable ... question ... replacements for ... output. ... Please ... Cosworths tend to have a history of being...
Guess i shouldn't complain, the one that's on it now is a Pep Boys job that Dad had put on it probably 10 years ago now. ;) Thanks!! Cliff Payne I Series...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
