http://denver.craigslist.org can be both useful and hilarious (some people think their junk is worth way too much). I got my 99 well below blue book a few...
The best years are from 92-95'.? The reason is that parts are interchangeable for these years and reliability is the best with these years.? I have a 99' and a...
This is for my 16 year old so a mild lift to stock would be fine. I do know that I want the 4.0L engine. I would like a STD trans but she wants the automatic....
I was thinking 91 and newer, I was told that in 91 they started using the better FI on the 4.0L Thanks Tom ... interchangeable for these years and reliability...
That is correct on the FI I would also go with the Automagic (aw-4), which in my opinion, is?a much better tranny than the ax15 stick. I am in Lakewood if i...
What would you think is a good reasonable price for a 91-96 Cherokee with the 4.0L std trans and around 150k miles? Thanks Tom ... (some people ... blue book a...
Between $1,500-$3K depending on the condition. There are a bunch of them for sale on www.craigslist.com for Denver. Have fun - they're good rigs and we've had...
I saw a nice one today with a 4cyl engine 5 speed. Is it worth the work to swap out the 4 cyl for a 4.0L engine. Is this a bolt on swap if I have a parts car...
No, it's not really worth the time and effort unless you have nothing else to do - there are plenty of 4.0L in-line 6 cyl versions available for the same price...
Or if you get both vehicles real cheap. I did that once. Took an 85 Pioneer with a bad frame for $200 and put the engine in a 86 for $500 with a good body....
so i put a 99 ford exploder rear end in my 89', does anyone have any info on proprtioning valves for the brake line? I need to get more pressure to the rear...
Get a aftermarket proportioning valve and bypass the original. Summit carry's them amongst other places. Toby ************************************** See what's...
I have the chance to get a good used NP231 from a wrangler with a 5 speed. Can that be swapped into a Cherokee with an automatic. I understand that the input...
The NP231 is out of a 92 Wrangler and the Cherokee is a 89 or 90 depending on which one we get. I see that there is a difference on the cut of the input gears ...
well the input gear for the cherokee should be a short 21 spline on the cherokee and a long 23 spline on the wrangler case. You will need to find a 21 spline...
Same to you Ron and the rest of the CO-XJ clan - just got the bird in the oven and am watching the Packers vs Lions game. Hope you're relaxing as well....
Much relaxing being done here. We went out so we wouldn't have to cook, that was about 11ish, then napped all afternoon and went to my Mom's for desert and...
Hey all! The board has been really quiet but I'll put this out... 95 XJ witha about 196K on it. Runs really good..when it starts. When it's sat for a while...
My XJ already has a 3" suspension lift with new coils and leafs. I just recently put 31" tires on it and there is a little bit of rubbing. I know that there...
Bryan, have you just considered trimming off the offending area that might be rubbing under full compression or when turning? It's better to keep the COG lower...
If you don't already have a 'puck' spacer on the coils and a longer leaf spring shackle, that's all that you'll need. A 1" coil spring spacer, and a 1" lift...
Thanks guys, Its a 97' and I am going to be doing some trimming but I don't really see that doing much accept letting me drive around town without any rubbing....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
