If those 3.73's don't get used, let me know. Wally is looking for the front setup. He toasted a pinion bearing and seized everything up. The housing was red...
Do you still have the driveshaft? Can you give me the length of it please? Where are you located? I am in Cody, WY. Thanks, Sean ... I don't ... clear the ...
Will do, though he said he needed both. How's things with you these days Brian? Aaron ... From: BrianG <fngearhead@...> Sent: Dec 1, 2004 1:41 AM To:...
Things are going fine. The XJ needs a motor. 240K and rear main leaking pretty good. I've replaced it 2 times in the last year. I think the crank surface is...
Glad you had some fun while the rest of us were slaving away and wheeling...:) I'll keep an eye out for motors - just helped one of my buds source one last...
My dad picked up a TJ at the end of the summer and he's finally got the itch to start lifting it. For now he just wants to put in some coil spacers. So my...
Your in luck, have one from a 99, its maroon though and have the endcaps David ... Preferably black. Thanks, ... __________________________________ Do you...
Cory, I called you last week about the D44, sorry about not calling you back with thanksgiving and stuff. I'm still interested in the rear end if you still...
Thanks David, I was offered a black one a few minutes ago. I'll let you know if I hear of some one to take it off your hands. JohnJohn ... [Message truncated....
im presently running a 3.5"RE super flex kit with 31" tires on d30 and 8.25 axles with 3.07 gears. i already have a problem with acceleration in 5th only...
I've got 32"s on with 3.55s and it's a dog, so 33's with 3.07s will probably be pretty bad. A stick can run slightly smaller gears than an auto. but I still...
Hey man give me a call whenever is convinient to you(time of night doesn't matter to me). Thanks again Cory darrick mittlestadt <xjdm@...> wrote: Cory, I...
Actually, I think you'll hear some recommendations to regear before anything else. You'd do well with 4.10s at a minimum, but 4.56 or even 4.88 as a better...
iI you dont lift it your drive shaft angle wont change so thats not a problem, unless u lift it then you may need the SYE. like said before i would suggest new...
still have it, hit me back channel ... pick it up? ... <beast80221@y...> ... though ... around? ... viruses. ... __________________________________ Do you...
Matt, You will need to trim to fit those 33's on a 3.5" lift. Though you should be able to swing 33's with good articuation and some trimming at 5". A good...
Jim, I suspect Matt is a few years from 35s and all the expense it will take to make a dependable combo with 35s. I have snapped a D30 u-joint with 31's,...
Hopefully he won't blow the D30 joints from a stop sign...shouldn't be in 4wd on the pavement anyway ;-) I'm running 4.56 and 32s right now and although that...
Not sure if there would be any interest here, but I am selling my set of 38's. They are 38/13/16 tsl's on 16x7" chrome rims. I would love to just trade them...
Hey, you never know about these newbies ;) My 98' gets 15 city and 20-21 hwy on the 3.55/31 MT combo I have, though OD use did suffer a little and only is...
I run 8" of lift with 35"s and 4.10 gears, no SYE as of yet. D30 and D44 axles. As for the question of can you run 33"s with 3.07 gears, yes you can. The ...
I've been running 36's and 4.11 gears on my green beast with 5-spd...until I can get them regeared! Aaron Jim, I suspect Matt is a few years from 35s and all...
I ran a D30 with 260x u-joints with 410s and 35s for quite some time (automatic trannie and alumn 15x10 rims). I'm easy on the skinny pedal though. Since then,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
